Intel VIA K8T800 User Manual Download Page 40 | Manualshive

Page: 40 / 92

background image

BIOS

Page 4-6

APIC Mode

This item allows you to enable APIC (Advanced Programmable Interrupt Controller)
functionality. APIC is a chip that provides symmetric multiprocessing (SMP) for its
Pentium systems. The default is Disabled.
Options: Enabled, Disabled.

MPS Version Control For OS

Specifies the Multiprocessor Specification (MPS). Version 1.4 supports multiple PCI
bus configurations by incorporating extended bus definitions. Enable this for
Windows NT or Linux. For older operating systems, select Version 1.1.
Options: 1.1, 1.4.

OS Select For DRAM > 64 MB

Some operating systems require special handling. Use this option only if your
system has greater than 64 MB of memory. The default is Non-OS2.

OS2

:

Select this if you are running the OS/2 operating system with greater
than 64 MB of RAM.

Non-OS2

: Select this for all other operating systems and configurations.

Video BIOS Shadow

This option allows video BIOS to be copied into RAM. Video Shadowing will
increase the video performance of your system.
Options: Enabled, Disabled.

«
...
38
39
40
41
42
...
»

Summary of Contents for VIA K8T800





























































































Reviews:

No comments

Related manuals for VIA K8T800

Brand: GE Pages: 4

Brand: Paradox Pages: 4

Brand: ebm-papst Pages: 16

Brand: Tripp Lite Pages: 20

Brand: Furuno Pages: 24

EK-FB GA AX370 Gaming RGB Monoblock

Brand: ekwb Pages: 2

Brand: NA Pages: 22

Extreme Gaming VGA Cooler GV1000

Brand: ZALMAN Pages: 7

Brand: Eaton Pages: 14

Brand: Rolls Pages: 1

Brand: Xilinx Pages: 29

Brand: ATTO Technology Pages: 2

Brand: Kordis Pages: 31

Brand: Lanpro Pages: 3

Brand: Lefroy Brooks Pages: 10

ExpressCard 11-in-1 Reader/Writer

Brand: SIIG Pages: 8

Brand: OWC Pages: 9

Brand: Xaoc Devices Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands