Intel S975XBX2 - Workstation Board Motherboard Specification Download Page 75

Page: 75 / 102

Technical Reference

2.13

Environmental

Table 36 lists the environmental specifications for the board.

Table 36. Environmental Specifications

Parameter Specification

Temperature

Non-Operating -40

C to +70

Operating

C to +55

Shock

Unpackaged

50 g trapezoidal waveform

Velocity change of 170 inches/second²

Packaged

Half sine 2 millisecond

Product Weight (pounds)

Free Fall (inches)

Velocity Change (inches/sec²)

<20

167

21-40

152

41-80

136

81-100

118

Vibration

Unpackaged

5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz

20 Hz to 500 Hz: 0.02 g² Hz (flat)

Packaged

5 Hz to 40 Hz: 0.015 g² Hz (flat)

40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz

Summary of Contents for S975XBX2 - Workstation Board Motherboard







































































































Search results

Summary of Contents for S975XBX2 - Workstation Board Motherboard

Reviews:

Intel S975XBX2 - Workstation Board Motherboard, Specification, Page: 75 / 102

Search results

Summary of Contents for S975XBX2 - Workstation Board Motherboard

Reviews: