Intel R2000LH2, Quick Installation User'S Manual

Page: 8 / 20

4
General Installation Process
9
Install Memory Modules
DDR3 DIMM Memory Ide ntification:
Other
Memory
DDR3
CAUTION:
Observe normal ESD (ElectroStatic
Discharge) procedures to avoid possible damage to
system components.
DIMM notch and socket bump must align as shown below.
8
Install Processor Heatsink(s)
NOTE : Heatsink styles may vary.
Remove the protective film on the TIM if present.
D
CAUTION: The heatsink has thermal interface
material (TIM) on the underside of it. Use caution so
that you do not damage the thermal interface material.
Use gloves to avoid sharp edges.
E
C
A
B Align heatsink fins to the front and back of
the chassis for correct airflow.
Airflow goes from front-to-back of chassis.
Each heatsink has four captive fasteners and
should be tightened in a diagonal manner using
the following procedure:
Using a #2 Phillips* screwdriver,
start with screw 1 and engage screw
threads by giving it two rotations
and stop. (Do not fully tighten.)
Proceed to screw 2 and engage screw
threads by giving it two rotations and
stop. Similarly, engage screws 3 and 4.
Repeat steps C and D by giving each
screw two rotations each time until
each screw is lightly tightened up to
a maximum of 8 inch-lbs torque.
C
OPEN 1st
CLOSE 1st
Processor
Socket
AIRFLOW
Chassis Front
2
3
1
4
A
B
TIM
D
CAUTION:
Do not
over-tighten
fasteners.
E
CPU 1 Socket CPU 2 Socket
CPU 4 Socket CPU 3 Socket
DIMM_E1 DIMM_E2 DIMM_E3 DIMM_F1 DIMM_F2 DIMM_F3
DIMM_L1 DIMM_L2 DIMM_L3 DIMM_M1 DIMM_M2 DIMM_M3 DIMM_J1 DIMM_J2 DIMM_J3 DIMM_K1 DIMM_K2 DIMM_K3 DIMM_R1 DIMM_R2 DIMM_R3 DIMM_T1 DIMM_T2 DIMM_T3 DIMM_N1 DIMM_N2 DIMM_N3 DIMM_P1 DIMM_P2 DIMM_P3
DIMM_G1 DIMM_G2 DIMM_G3 DIMM_H1 DIMM_H2 DIMM_H3 DIMM_C1 DIMM_C2 DIMM_C3 DIMM_D1 DIMM_D2 DIMM_D3 DIMM_A1 DIMM_A2 DIMM_A3 DIMM_B1 DIMM_B2 DIMM_B3
Install Memory Modules ...continued
Memory Configurations and Population Order:
For best performance, a minimum of four DIMMs per CPU is
recommended, populated in the blue slot of each memory channel.
In a single-processor configuration, always populate A1 DIMM first.
In a four-processor configuration, always populate A1 DIMM for CPU1, E1
DIMM first for CPU2, J1 for CPU3, and N1 for CPU4.
NOTE : For additional memory configurations, see the Service Guide
available at http://www.intel.com/p/en_US/support .
Memory sizing and configuration is supported only for qualified DIMMs
approved by Intel
®
. For a list of supported memory, go to:
http://serverconfigurator.intel.com .
Intel ® Server Board S4600LH2/LT2
Install Processor(s) ...continued
Push down on the locking lever on the CLOSE 1st side.
F. Latch the Locking Lever
A
B
Slide the tip of the lever under the notch in the load plate.
Make sure the load plate tab engages under the socket lever when
fully closed.
C
Repeat the steps to latch the locking lever on the other side.
OPEN 1st
CLOSE 1st
REMOVE
REMOVE
CLOSE 1st
B
A
OPEN 1st
CLOSE 1st
C
NOTE : Latch the levers in the
order as shown.