Intel IXP28 Series Manual Download | Manualshive

Page: 81 / 154

background image

Hardware Design Guide

81

IXP28XX Network Processor

QDR SRAM

4.7

TCAM/SRAM/Coprocessor Interface

In certain cases it may be desirable to implement a connector in the QDR interface to accommodate
a third-party QDRII-LA1-compliant coprocessor or an upgradable QDR memory module. The
Intel BKM for this is to provide the IXP28XX QDR interface through a 2 x 57 shrouded 114-pin
Mictor* connector. The connector has all the QDR signals from a single channel and JTAG
interface. In addition, power is provided in the form of 1.5 V, 1.8 V, and 3.3 V. The current for the
1.5 V and 1.8 V is limited to 0.5 A and 2.5 A, respectively. This current supply provides the power
support for up to four QDRII SRAMs.

4.7.1

TCAM/SRAM/Coprocessor Interface — Base Card Side

This part of the interface runs between the ingress IXP28XX network processor and the Mictor*
connector on the base card side. All traces are matched in length to within ±10 mils and have the
same nominal line impedance of 50

Ω

.

4.7.1.1

Interface Topologies

This part of the interface has a topology of a point-to-point configuration between the IXP28XX
network processor’s I/O buffer and the Mictor* connector. The rest of the topologies are found on
the TCAM/SRAM/coprocessor card and are different for different signals (Address, D, etc.).

4.7.1.1.1

Address, D, CONTROL, Q, and K-Clocks Signals

Figure 45

illustrates topologies for address, D, CONTROL, Q, and K-clocks.

Figure 44.

Voltage QDR V

REF

Divider Example for Each QDR Channel

Downloaded from

Elcodis.com

electronic components distributor

«
...
79
80
81
82
83
...
»

Summary of Contents for IXP28 Series



























































































































































Reviews:

No comments

Related manuals for IXP28 Series

Brand: ZALMAN Pages: 20

Brand: National Instruments Pages: 11

Brand: Patton electronics Pages: 16

Brand: ETAS Pages: 69

Brand: Alesis Pages: 61

Brand: Z3 Technology Pages: 67

Brand: Patton electronics Pages: 145

DVI-Vision-IP-Fiber

Brand: G&D Pages: 240

Brand: ETAS Pages: 84

Brand: SilverStone Pages: 28

Wireless Outdoor Bridge XI-1500-IH

Brand: IMC Networks Pages: 13

BPN-SAS3-116A-N10

Brand: Supermicro Pages: 8

Brand: Patton electronics Pages: 8

Brand: M86 Security Pages: 512

Brand: Omnia Pages: 130

System 200V PC 288

Brand: VIPA Pages: 54

Brand: ICP DAS USA Pages: 60

Brand: PairGain Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands