manualshive.com logo in svg

Intel BLKD945GPMLKR, Technical Product Specification, Page: 45 / 94

Share
Download
Intel BLKD945GPMLKR Technical Product Specification Download Page 45

Product Description 

 45 

1.12.2.11  +5 V Standby Power Indicator LED 

The +5 V standby power indicator LED shows that power is still present even when the computer 
appears to be off.  Figure 14 shows the location of the standby power indicator LED. 

 CAUTION 

If AC power has been switched off and the standby power indicator is still lit, disconnect the power 
cord before installing or removing any devices connected to the board.  Failure to do so could 
damage the board and any attached devices. 

CR3J1

OM17838

 

Figure 14.  Location of the Standby Power Indicator LED 

1.13  Trusted Platform Module (Optional) 

The optional Trusted Platform Module (TPM) is a component on the desktop board that is 
specifically designed to enhance platform security above-and-beyond the capabilities of today’s 
software by providing a protected space for key operations and other security critical tasks.  Using 
both hardware and software, the TPM protects encryption and signature keys at their most 
vulnerable stages—operations when the keys are being used unencrypted in plain-text form.  The 
TPM is specifically designed to shield unencrypted keys and platform authentication information 
from software-based attacks. 

 

For information about  

Refer to 

TPM 

http://www.intel.com/design/motherbd/pm

 

 

Summary of Contents for BLKD945GPMLKR































































































Reviews:

No comments