Intel BLKD945GPMLKR Technical Product Specification Download Page 33

Page: 33 / 94

Product Description

Side Surround
Left and Right/
Line In/Retasking Jack
[Blue]

Line Out/Retasking Jack

[Lime Green]

Mic In/Retasking Jack

[Pink]

OM17816

Mic In

Front Panel

Audio Connectors

Line Out

Surround Left and Right/Retasking Jack

[Black]

Center channel and LFE (Subwoofer)/

Retasking Jack [Orange]

S/PDIF Digital Audio Out

Optical

Figure 9. Front/Back Panel Audio Connectors

Figure 10 is a block diagram of the 8-channel (7.1) audio subsystem.

82801GH

I/O Controller

Hub

(ICH7DH)

OM18264

Intel

High Definition

Audio Link

Sigmatel

9220/9223

Audio Codec

Line Out/Retasking Jack

Mic In

Line In/Side Surround L-R/Retasking Jack

Mic In/Retasking Jack

S/PDIF

Surround Left-Right/Retasking Jack

Center and LFE/Retasking Jack

Line Out

Back

Panel

Front

Panel

Figure 10. 8-channel (7.1) Audio Subsystem Block Diagram

Summary of Contents for BLKD945GPMLKR































































































Search results

Summary of Contents for BLKD945GPMLKR

Reviews:

Intel BLKD945GPMLKR, Technical Product Specification, Page: 33 / 94

Search results

Summary of Contents for BLKD945GPMLKR

Reviews: