manualshive.com logo in svg

Intel BLKD945GPMLKR, Technical Product Specification, Page: 35 / 94

Share
Download
Intel BLKD945GPMLKR Technical Product Specification Download Page 35

Product Description 

 35 

1.10.2.2  RJ-45 LAN Connector with Integrated LEDs 

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 11).   

Green LED

Yellow LED

OM15076

 

Figure 11.  LAN Connector LED Locations 

Table 5 describes the LED states when the board is powered up and the 10/100 Mbits/sec LAN 
subsystem is operating. 

Table 5. 

LAN Connector LED States 

LED Color 

LED State 

Condition 

Off 

LAN link is not established. 

On 

LAN link is established. 

Green  

Blinking 

LAN activity is occurring. 

Off 

10 Mbits/sec data rate is selected. 

Yellow 

On 

100 Mbits/sec data rate is selected. 

1.10.3  Gigabit LAN Subsystem 

The Gigabit (10/100/1000 Mbits/sec) LAN subsystem includes the Intel 82573L controller and an 
RJ-45 LAN connector with integrated status LEDs. 

1.10.3.1 Intel

®

 82573L Gigabit Ethernet Controller 

The Intel 82573L Gigabit Ethernet Controller supports the following features: 

•

 

PCI Express link 

•

 

10/100/1000 IEEE 802.3 compliant 

•

 

Compliant to IEEE 802.3x flow control support 

•

 

Jumbo frame support 

•

 

TCP, IP, UDP checksum offload 

•

 

Transmit TCP segmentation 

•

 

Advanced packet filtering 

•

 

Full device driver compatibility 

•

 

PCI Express Power Management Support 

Summary of Contents for BLKD945GPMLKR































































































Reviews:

No comments