background image

INDEX

 

USER MANUAL 

 OPTIMA-T10 6K/10K (UL) 

 

 

www.xmart-ups.com 

VER.190731-GA2UL (ENG)

 

 

1.

 

GENERAL SAFETY INSTRUCTIONS 

 

WARNING

: It is required to read and understand this manual. Follow all instructions given in this manual for starting up and operating this 

product. Only qualified technician must start-up, operate and maintain this product. Keep manuals as a guide for future consults. 

UPS manufacturer or distributor will never be responsible for any accident produced by lack of knowledge or negligent practices at the 

moment of install, starting up or maintain this product. UPS manufacturer or distributor is not liable for any damage that might rise from 

misusing this unit or defective installation.  

 

SAFETY: 

 

ELECTRIC SHOCK RISK

 

This product operates with dangerous voltages. It must be installed, operated and maintained ONLY by qualified technicians trained for 

this kind of products. Service personnel MUST know and understand very well all electric risks related to this product. 

If you are not qualified technician do not try to install, operate or repair this product. 

CAUTION:

 There are dangerous voltages in the UPS power outlets although the equipment is not plugged to power line. 

CAUTION:

 Inside this equipment, due to internal batteries, there are ALWAYS dangerous voltages, EVEN the UPS is OFF and unplugged. 

CAUTION:

 There are dangerous voltages in internal DC Capacitors. Wait at least 10 minutes after turning off UPS before opening it to 

access inside. 

CAUTION:

 Power off UPS and unplugged it from AC Line before opening it to Access inside this unit. 

CAUTION:

 Before starting the opening procedure, remove all jewelry and metallic objects such as: Rings, Watches, Bracelets, etc., because 

they could contact conductive parts and components inside the UPS and this might cause discharges and/or short circuits. Make sure 

using tools properly isolated to avoid electrical risks. 

 

WARNING:

 This product has been designed to be used indoors protected from water, direct sun light, dust and extreme temperature. 

WARNING:

 Do not put any object on the UPS; do not apply any force over UPS. Do not cover UPS ventilation. 

WARNING:

 This UPS must be connected to appropriate electrical service according to selected model. Technical specs label in the UPS 

shows the UPS power ratings. DO NOT connect this UPS to any of its own power outlets, this could damage the unit permanently. 

WARNING:

 Do not connect AC motor-based equipment without a careful sizing of the UPS based on inrush current instead of average 

current. Inrush current typical of motor-based system could overload this UPS. 

WARNING:

 In case of emergency, power-off UPS and turn it off by <OFF> button in front panel. Then call technical service.

 

 

 

 

INFORMATION FOR THE PROTECTION OF ENVIROMENT 

 UPS SERVICING

 

This  UPS  and  batteries  make  use  of  components  dangerous  for  the  environment  (electronic  cards,  electronic  components).  The 

components removed must be taken to specialized collection and disposal centers. 

 

NOTICE TO EUROPEAN UNION CUSTOMERS: DISPOSAL OF OLD APPLIANCES 

This product has been supplied from an environmentally aware manufacturer that complies with Waste Electrical and Electronic 

Equipment (WEEE) Directive 2002/96/CE. The “crossed

-

out wheelie bin” symbol at left is placed on this product to encourage 

you to recycle wherever possible. Please be environmentally responsible and recycle this product through your recycling facility 

at its end of life. Do not dispose  of this product as unsorted municipal waste. Follow local municipal waste electrical and 

electronic equipment (WEEE). 

 

 

Summary of Contents for (UL)













































Reviews: