Integra DTR-40.4 Instruction Manual Download

Page: 14 / 104

Connections

En-14

Connecting AV components

If your TV doesn’t support Audio Return Channel (ARC), you
need to connect an optical digital cable together with the
HDMI cable to the AV receiver.

• Before making any AV connections, read the manuals

supplied with your AV components.

• Don’t connect the power cord until you’ve completed and

double-checked all AV connections.

• Push plugs in all the way to make

good connections (loose connections
can cause noise or malfunctions).

• To prevent interference, keep audio

and video cables away from power
cords and speaker cables.

AV Cables and Jacks

■

HDMI

HDMI connections can carry digital video and audio.

■

Component video

Component video separates the luminance (Y) and color
difference signals (P

, P

), providing the best picture

quality (some TV manufacturers label their component
video sockets slightly differently).

■

Analog RGB

This is a conventional analog interface to connect a PC and
a display device (also called D-Sub or D-subminiature).

■

Composite video

Composite video is commonly used on TVs, DVDs, and
other video equipment.

■

Optical digital audio

Optical digital connections allow you to enjoy digital
sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as coaxial.

■

Coaxial digital audio

Coaxial digital connections allow you to enjoy digital
sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as optical.

■

Analog audio (RCA)

Analog audio connections (RCA) carry analog audio.

For PCM signals, the supported sampling rates are
32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4 and
192 kHz are also supported.

Note

• The AV receiver does not support SCART plugs.
• The AV receiver’s optical digital jacks have shutter-type covers

that open when an optical plug is inserted and close when it’s
removed. Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight

when inserting and removing.

About AV Connections

HDMI cable

Other cables

: Video & Audio

: Video

Game console

Blu-ray Disc/

DVD player

TV, projector, etc.

AV receiver

TV, projector, etc.

AV receiver

Game console

Blu-ray Disc/

DVD player

: Audio

Green

Blue

Red

Yellow

Right!

Wrong!

Orange

White

Red

Summary of Contents for DTR-40.4









































































































Search results

Summary of Contents for DTR-40.4

Reviews:

Related manuals for DTR-40.4

Brands by name

Popular brands

Integra DTR-40.4, Instruction Manual

Search results

Summary of Contents for DTR-40.4

Reviews:

Related manuals for DTR-40.4

Brands by name

Popular brands