InStep Sync Owner'S Manual Download Page 5

Page: 5 / 28

• Do not allow any of the child’s body, clothing, shoe laces, or

toys come into contact with a moving trailer.

• Take proper steps (clothing, ventilation, hydration) to protect

the child from exposure hazards such as wind chill and heat

exhaustion. These hazards will have a greater impact on the

less active passenger.

TRAILER USE WARNINGS

• Failure to comply with the manufacturer’s instructions can

lead to serious injury or death of the passenger/rider

• Do not install inside the trailer, a car seat or any other seating

device not approved by manufacturer.

• Before each ride, ensure the attached trailer does not interfere

with braking, pedaling, or steering of the bicycle.

• Do not add a seat pad (mattress) thicker than 2.5” (63.5 mm).
• Parcels or accessories placed on the trailer may cause the

trailer to become unstable.

• Do not place items on the trailer. Hazardous conditions may

exist if package carrying accessories are added to the product.

• This product may contain a chemical known to the State

of California to cause cancer, birth defects, or other

reproductive harm.

• Check the trailer for damage. Do not use if damaged.
• Be sure the fasteners are tight. Tighten if necessary.

• Over inflation of tires may result in failure and risk of serious

injury. Do not exceed maximum pressure as shown on tires.

• If necessary inflate the tires to within the range shown on

the tire sidewall. Always use a foot or hand pump to inflate the

tires.

• The safety flag and reflectors must be in place. Do not use the

trailer without the safety flag and reflector in place.

• Always have the canopy in place.
• Do not make any modifications to the trailer as it increases the

risk of failure.

• Accessories not approved by the manufacturer must not

be used.

SAFE RIDING WARNINGS

• Child must wear a certified helmet.
• Be sure the brakes work properly. Braking distance is

increased when pulling a trailer.

• Avoid braking suddenly.
• Always maintain a safe speed. The trailer is not intended for

use at high speeds. Do not exceed 10 MPH.

• The trailer requires a wide turning radius. Do not turn sharply.

Sharp changes in direction may cause a tip over.

continued on next page

WARNING!

InStep Sync Trailer 2

Summary of Contents for Sync





























Search results

Summary of Contents for Sync

Reviews:

Related manuals for Sync

Brands by name

Popular brands

InStep Sync, Owner'S Manual

Search results

Summary of Contents for Sync

Reviews:

Related manuals for Sync

Brands by name

Popular brands