InStep Sync Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 28

background image

ADJUSTING THE SHOULDER STRAPS

InStep Sync Trailer 18

Figure 5.2

1

2

3

4

There are three slots on the back of the seat. These slots are used

to adjust the proper height of the shoulder straps to your child’s

height. To adjust the shoulder strap height:

❶ Starting from the back of the seat, pull the shoulder strap

anchor away form the seat.

❷ Insert the anchor through the slit in the seat, pushing it

towards the front.

❸ Insert the anchor through the slit in the front of the seat at the

desired height.

❹ Pull the strap and anchor all the way through to the back.

Make sure the strap is properly anchored on the seat back.

Repeat these steps for the opposite strap. Figure 5.2

«
...
19
20
21
22
23
...
»

Summary of Contents for Sync





























Reviews:

No comments

Related manuals for Sync

Brand: Voxx Pages: 7

Brand: Sunx Pages: 2

Brand: FeiYu Tech Pages: 5

Brand: FEIYUTECH Pages: 19

Brand: FeiYu Tech Pages: 25

Brand: FEIYUTECH Pages: 16

INDUSTRIAL Series

Brand: QC Conveyors Pages: 44

Brand: Kathrein Pages: 7

Brand: Kathrein Pages: 2

Brand: Omnicomm Pages: 20

Brand: omnicharge Pages: 12

Legend G3 738 NGK

Brand: Valor Pages: 6

Brand: Trace2O Pages: 9

Brand: ICON Pages: 2

Power commander GSXR750

Brand: Dynojet Pages: 4

GTM 10 - TMC Module

Brand: Garmin Pages: 1

Brand: Razorri Pages: 26

Brand: Dynojet Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands