background image

TimerLinc Owner’s Manual  

 

Page 18 of 18 

 

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the 
date of purchase, this product will be free from defects in material and workmanship and will perform in 
substantial conformity to the description of the product in this Owner’s Manual. This warranty shall not 
apply to defects or errors caused by misuse or neglect. If the product is found to be defective in material 
or workmanship, or if the product does not perform as warranted above during the warranty period, Seller 
will either repair it, replace it, or refund the purchase price, at its option, upon receipt of the product at the 
address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or 
error. The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s 
liability with respect to this product. For repair or replacement during the warranty period, call the 
INSTEON Gold Support Line at 800-762-7845 with the Model # and Revision # of the device to receive 
an RMA# and send the product, along with all other required materials to:  

Smarthome, Inc. 
ATTN: Receiving Dept.  
16542 Millikan Ave. 
Irvine, CA 92606-5027

 

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express 
or implied, including any warranty or merchantability or fitness for a particular purpose. Any implied 
warranty, including any warranty of merchantability or fitness for a particular purpose, which may not be 
disclaimed or supplanted as provided above shall be limited to the two-year of the express warranty 
above. No other representation or claim of any nature by any person shall be binding upon Seller or 
modify the terms of the above warranty and disclaimer.  

Home automation devices have the risk of failure to operate, incorrect operation, or electrical or 
mechanical tampering. For optimal use, manually verify the device state. Any home automation device 
should be viewed as a convenience, but not as a sole method for controlling your home.  

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from 
possession or use of this device, including without limitation damage to property and, to the extent 
permitted by law, personal injury, even if Seller knew or should have known of the possibility of such 
damages. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion 
or limitation of damages, in which case the above limitations and/or exclusions may not apply to you. You 
may also have other legal rights that may vary from state to state.  

INSTEON Technology Patent 

U.S Patent No. 7,345,998, International patents pending  

© Copyright 2011 

Smarthome, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, 

www.smarthome.com

 

 

Rev 04-05-2011 

Summary of Contents for TimerLinc 2456S3T



















Reviews: