background image

Page 10 of 10 

2993-xx2 - Rev: 3/11/2014 9:21 AM 9:21:55 AM 

Certification and Warranty 

Certification 

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark 
signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian device safety standards, that the 
manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-up inspections to verify continued conformance.  

ETL/UL Warning (Safety Warning) 
CAUTION: 

To reduce the risk of overheating and possible damage to other equipment, do not install this device to control a receptacle, a motor-operated appliance, a 

fluorescent lighting fixture, or a transformer-supplied appliance.  
Gradateurs commandant une lampe a filament de tungstene – afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres materiels, ne pas 
installer pour commander une prise, un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.  

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of purchase,  this product will be free from defects in 
material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or 
errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product does not perform as warranted above during the 
warranty period, Seller will either repair it, replace it, or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with 
proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s 
liability with respect to this product. For repair or replacement during the warranty period, call INSTEON at 800-762-7845 with the Model # and Revision # of the device 
to receive an RMA# and send the product, along with all other required materials to:  

 
INSTEON 
ATTN: Receiving 
16542 Millikan Ave. 
Irvine, CA 92606-5027 

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or merchantability or fitness 
for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or supplanted 
as provided above shall be limited to the two-year of the express warranty above. No other representation or claim of any nature by any person shall be binding upon 
Seller or modify the terms of the above warranty and disclaimer.  
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify the device 
state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.  

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including without limitation 
damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states do 
not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case the above limitations and/or exclusions may not 
apply to you. You may also have other legal rights that may vary from state to state.  

U.S Patent No. 7,345,998, International patents pending (see www.insteon.com). 
© Copyright 2014 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, www.insteon.com

 

 

Summary of Contents for 2993-222











Reviews: