METAL WIRELESS KEYPAD
06
81
1 - Introduction
The Wireless Keypad ( PN 050550 ) is an encoded radio keypad
operating at 433,92 MHz.The best use of the product is on applications
where an encrypted radio signal has to be used to control: gates, garage
doors, rolling shutters, sun-blinds, anti-burglar appliances, lightings,
etc. The code has a very high security coding system (19683 code
combinations). The radio transmission is enabled only after the dialing of a
security user code. There are up to 4+2 different channels that can
activate up to 6 different receivers or relays.
The internal memory can store up to 24 different
access
codes and 1
Master code.
The product fully complies with the European directives 89/336/CEE,
99/05/CE and Part. 15 of FCC Rules..
2 - Technical specifications
Number of keys: ......................................................................
...........
12
Number of channels:...........................................................
............
4 + 2
Supply: ............................................................................
...........
3,6 Vdc
Battery duration: ................................................
.........
about 24 months
Battery type:..........................................................
.....
Lit
h
ium LS14500
Current consumption: ( transmission ) ..................................
......
28 mA
stand-by...........................................................................
..............
0,8 uA
Operating frequency: ................................................
..........
433.92 MHz
Modulation: ....................................................................
.........
AM/ASK
E.r.p.:.................................................................................
.............
6 mW
Security Code combinations number: ..................................
.........
19683
User security code number:..................................................
...........
24+1
Transmission duration: .......................................
........
until press / 1 sec.
Range in open space: ......................................
..........
from 150 to 700 m
Operating temperature: ................................
........
.
Dimensions: ......................................................
......
.
Weight:...........................................................................
.............
.
IP Protection Grade: ..............................................................
..........
IP54
from 14 °F to 131 °F
5.7
x
3.07
x
1.25 in
3.24 oz
Part # 050550
NOTES:
The appliance uses
a lithium battery type
LS14500 3,6V. The removal
and the disposal of the
battery must have effected
before the elimination of
the appliance and according
to the current Regulations.
ATTENTION: - Danger of
explosion if the battery is
not replaced in the correct
way! Replace only with an
equal or equivalent type.
3 - Types
050550 : Fixed code Radio keyboard without tamper;
4 - Battery replacement
Remove the cover and extract the old battery from the bottom site of the
electronic card with an upward traction. Insert the new battery on the
battery location, respecting the right polarity.
(NOT AA BATTERY)
FCC ID : PWNF1002000029
This device complies with FCC Rules Part 15 Operation is
subject to the following two conditions:
1) This device may not cause harmful interferences;
2) this device must accept interference that may
cause undesired operation.
M a d e i n Italy
5 - Installation steps
1. Locate the best position for the installation, avoid metallic
enclosures that could decrease the RF emission.
2. Mark the location of the mounting holes using the base as a drilling
template.
3. Drill the mounting holes and insert the plugs.
4. Remove the protection strip from the seal.
5. Assemble the base and seal together.
6. Install the base with the screws supplied.
7. Install the keypad to the base.
8.
Secure in place with the 2 screws supplied.
6 - Programming wireless keypad
Terms to understand
Master Password:
The 5-digit code used to access programming
features. Factory default is “11111.” This needs to be changed by the
user for security reasons.
If changed record new password.
Access Code:
The 1 to 5-digit code used to open the gate (24 uni
que
codes are possible). If access code is less than 5 digits it requires the
"B"
button after code is entered. Example: “2 B.” If the code is 5 digit
button
B is not required.
Relay 1:
The receiver has 2 relays. P1 (relay 1) is factory wired t
o
push/button
input on the control board.
Relay 2:
The receiver has 2 relays. P2 (relay 2) is factory wired to
“Open / Free Exit” input on the control board.
Security Code (Dip Switch Code):
The keypad does not have dip
-
switches. Instead, the receiver has a learn mode which can be used to
program the keypad to the receiver. The keypad can also be
manually programmed if a transmitter is being used.
See “Changing Security Code” on paragraph 1
0
.
PUK Code:
“Password Unblocking Key.” The PUK code is located
inside the keypad and is needed when the master password has been
lost. Copy and store in a safe place for future reference. Must be 5
digits long lead with zeros.
“
A
” Key:
located on the keypad is used to cancel last command
entered.
Button
5" Blinks:
When blinking, the keypad is sending a signal
to the receiver.
Valid access code was entered.
7 -
Master
Password
7KHNH\SDGKDVD0DVWHU3DVVZRUGIDFWRU\VHWWR³´
,IWKH
0DVWHU3DVVZRUGUHPDLQVWKHGHIDXOWRQHWKHIROORZLQJIXQFWLRQV
DUHDOORZHG
v
,QVHUWLRQRIQHZ$FFHVV&RGHV
v
&DQFHOODWLRQRIVWRUHG$FFHVVFRGHV
v
5HSODFHPHQWRIWKH0DVWHU3DVVZRUG
7KH0DVWHU3DVVZRUGDQGWKH8VHUFRGHFDQKDYHXSWRGLJLWV,I
WKHFKRVHQFRGHLVVKRUWHUWKDQGLJLWVSUHVVWKHNH\³%´DIWHUWKH
ODVWGLJLWWRFRPSOHWHWKHQXPEHUDVLQGLFDWHGEHORZ
v
([DPSOH8VHUFRGH(QWHU%
v
([DPSOH8VHUFRGH(QWHU%
1RWH
'RQRWLQVWDOONH\SDGXQWLO³
Create Communication with
5HFHLYHU´KDVEHHQFRPSOHWHG
+
_
8 -
Keypad Programming
Create Access Code:
(Code you use to operate the gate)
*
CAN NOT BE THE SAME AS MASTER PASSWORD!
1.
2.
3.
Enter the Master Password “11111”. (this is the factory default
master password).
Enter “9” If correct, 2 short beeps (if 1 long beep is heard,
start over with step 1).
Enter the new Access Code (up to 5 digits), if less than 5
digits, “B” key is required.
4. Enter “9”
5. Enter the new Access Code again to verify.
6. Enter “1”. If this access code is for P1 (relay 1) Enter “2” if this
access code is for P2 (relay 2). See Note below.
7. If correct, 2 short beeps (if 1 long beep is heard, start over
with step1).
8.
Continue with “Create Communication with Receiver” to
complete programming.
Thank you for choosing this product.
Please read this manual carefully before using the product.
