Inspire Dual Lat/Row Assembly & Operation Manual Download Page 4

Page 1 

IMPORTANT SAFETY INSTRUCTIONS 

Please read this entire manual and familiarize yourself with all decals and 

warnings before using this Dual Lat/Row machine. 

 

• WARNING!  It is necessary to inspect this Dual Lat/Row machine 

  regularly to maintain safety and proper function. Please use the 

  maintenance schedule included towards the back of this manual.  

  Immediately replace any and all defective or worn parts.  Pay special 

  attention to moving parts such as the cables and pulleys and connections 

  to accessories. See General Maintenance section for complete details. 

 

• Use this Dual Lat/Row machine for its intended purpose as  described in 

  this Operation Manual or the Exercise Book. Do not use attachments not 

  recommended by the manufacturer. 

 

• Make sure bystanders are at least 5 feet away from the Dual Lat/Row 

  machine while it is in use.

 

 

• Keep children off the Dual Lat/Row machine at all times. 

 

• Keep the Dual Lat/Row machine away from walls and clear of any 

  obstructions. 

 

• Stop immediately if you experience shortness of breath, pain, or dizziness 

  during your workout.  Inspire strongly recommends consulting your 

  doctor before starting an exercise program. 

 

 

TOOLS REQUIRED FOR ASSEMBLY 

 

• Metric socket set (including 16mm, 17mm, and 19mm sockets) 

• Metric wrenches (16mm, 17mm, and 19mm) 

• 4mm, 5mm, and 6mm Allen wrenches (supplied in hardware pack)

 

• Adjustable wrench

 

• Philips screwdriver 

 

Summary of Contents for Dual Lat/Row
































Reviews: