Inovance EtherCAT MD800 Starting Manual Download Page 43

Page: 43 / 78

INOVANCE TECHNOLOGY EUROPE GmbH
MD800 EtherCAT Starting Guide_EN_v1.1_20211109.docx

7.2

BECKHOFF'S CONTROLLER

Beckhoff's TwinCAT master station is used as an example to describe the configuration of the SI-ECAT card.

NOTE

: The 100M Ethernet network adapter with Intel chip must be used. Other network adapters may not

support EtherCAT.

Install TwinCAT.

Windows XP system:

tcat_2110_2230

is recommended.

Windows 7 32-bit system:

tcat_2110_2248

is recommended.

Copy the EtherCAT configuration file (MD800_9Axis_V0.18.xml) of MD800 to the

TwinCAT installation directory.

TwinCAT2 directory:

TwinCAT\IO\EtherCAT

TwinCAT3 directory:

TwinCAT\3.1\config\IO\EtherCAT

TwinCAT3 is used as an example in the following section. The operation steps for TwinCAT2 are
similar.

Start TwinCAT.

Click

New Project

to create a project.

Summary of Contents for EtherCAT MD800















































































Search results

Summary of Contents for EtherCAT MD800

Reviews:

Related manuals for EtherCAT MD800

Brands by name

Popular brands

Inovance EtherCAT MD800, Starting Manual

Search results

Summary of Contents for EtherCAT MD800

Reviews:

Related manuals for EtherCAT MD800

Brands by name

Popular brands