Innowater PHRX Manual Download Page 4

Page: 4 / 19

INNOWATER PHRH

Page

1. Description

..............................................................

2. Instalation

..............................................................

3. Operating

................................................................

3.1. Main screen

............................................................

3.2. Secondary screen

....................................................

3.3. Start up. ON/OFF

.....................................................

3.4. Start up. Priming and acid level alarm

........................

4. pH configuration

.....................................................

4.1. Enable / Disable

......................................................

4.2. Setpoints

................................................................

4.3

4.4 Probe calibration

................................................

4.5. Factory calibration

..................................................

4.6. Dosing alarm

.........................................................

5. ORP configuration

.................................................

5.1. Setpoints

...............................................................

5.2. ON/OFF mode (with chlorinator)

...............................

5.3. Probe calibration

....................................................

5.4. Factory calibration

..................................................

Summary of Contents for PHRX




















Search results

Summary of Contents for PHRX

Reviews:

Related manuals for PHRX

Brands by name

Popular brands

Innowater PHRX, Manual

Search results

Summary of Contents for PHRX

Reviews:

Related manuals for PHRX

Brands by name

Popular brands