manualshive.com logo in svg

Innovx )DVW6ZLWFK#57, Installation & Operation Manual, Page: 30 / 116

Share
Download
Innovx )DVW6ZLWFK#57 Installation & Operation Manual Download Page 30

Using the Web Interface

Administrator Web Page

3-8

Innovx FastSwitch 24

200R205-000

Installation and Operation Manual

Issue 4

Weighted Round Robin (WRR)
This setting selects the preference given to packets in the switch's high-priority and low priority 
queue. These options represent the number of high priority packets sent before one low priority 
packet is sent. For example, 

5 High: 2 Low

 means that the switch will send 5 high priority 

packets before sending 2 low priority packets.

Qos Policy
This setting determines High Priority Levels; 0 to 7 priority level can map to high or low queue. 

Miscellaneous Configuration

The Miscellaneous Config. page, shown below, allows the following additional settings:

Collisions Retry Forever
Enable/Disable collisions retry forever.

Hash Algorithm
CRC-hash/Direct-map hash algorithm. Typical users are instructed not to change this setting.

IFG Compensation
Enable/disable IFG Compensation. Typical users are instructed not to change this setting.

802.1x Protocol
Enable/Disable 802.1x protocol.

Hardware Options

The size of hardware table such as MAC table, VLAN table, IP multicast table to the switch are 
configurable with some combinations and are displayed on this page.

Summary of Contents for )DVW6ZLWFK#57





















































































































Reviews:

No comments