Innovx )DVW6ZLWFK#57 Installation & Operation Manual Download Page 21 | Manualshive

Page: 21 / 116

Innovx )DVW6ZLWFK#57 Installation & Operation Manual Download Page 21

Installation & Connections

Overview

200R205-000

Innovx FastSwitch 24

2-5

Issue 4

Installation and Operation Manual

Command Syntax Conventions

In this manual, the following conventions are used to assist the user in properly entering CLI
commands, command parameters and choices.

Network Port Access Setup

Any in-band line port can be used for switch management configuration.
If DHCP is used to assign an IP address, type the following command at the prompt:

config network protocol <none/bootp/dhcp>

config network protocol dhcp

You must reboot the FS-24 for the DHCP to become effective.

Note

To configure the FS-24 using other interfaces, refer to Chapter 3, Using the Web Interface or

Chapter 4,

Command Line Interface

.

Table 2-5

Command Line Syntax Conventions

Command

Description

Command Name and

parameters

Commands displayed in Courier fonts must be typed exactly as shown.
Following the syntax of a command, an example usage of the
command is shown. Output of the command is shown either in Italics or
as a terminal capture.

<parameter>

The <> angle brackets indicates that the parameter is required for
executing the command.

[parameter]

The [] square brackets indicates that the parameter is optional.

choice1 | choice2

The | indicate that only one of the parameter should be entered.

ipaddr

This parameter is a valid IP address of four decimal bytes (separated
by .), each byte ranging from 0 to 255. The default IP is usually 0.0.0.0

macaddr

The MAC address format is six hexadecimal numbers separated by
colons, for e.g., 0:20:10:32:0e:40

slot.port

This parameter denotes a valid slot number and a valid port number.
For example 0.1 represents slot 0 port 1.

«
...
19
20
21
22
23
...
»

Summary of Contents for )DVW6ZLWFK#57





















































































































Reviews:

No comments