background image

 

Operating Manual  

      IP Telephone IP200 

                   - 26 -

- 26 -

 

 

6.

  User Setup menu 

6.1. Call 

diversion 

The Call Diversion menu allows you to be available even whilst absent.  

6.1.1 Diversion 

options 

The IP telephone supports three different types of call diversion: 

Permanent 
diversion 
(

Unconditional

In this case, calls are always diverted to another subscriber.  

Note: 
This diversion setting cancels the other diversion 
types. 
This setting diverts calls immediately. The party being 
called is therefore unable to answer the calls. 

 

Diversion if busy 
(

Busy

Calls are diverted if there is already an active call. 

Delayed 
diversion        
(

No reply

Calls are diverted if they are not answered within a certain time 
limit. 

Note: 
Unlike permanent call diversion, the latter two types 
allow you to accept calls within a pre-defined time 
period before they are diverted.  
 

 

 

Note: 
In the IP telephone’s initial state, an active call diversion is indicated by the 

 

symbol in the status line. For a permanent diversion, the diversion destination 
is also displayed. 

Summary of Contents for IP200









































Reviews: