INNACOMM W3100 User Manual Download Page 6

Page: 6 / 54

Supports the binding of the ports and the PVCs

Supports the 802.1Q and 802.1P protocol

Supports DHCP server

Supports NAT/NAPT

Supports static route

Supports firmware upgrade

：

WEB/tftp/ftp

Supports reset to factory default:reset, WEB

Supports DNS relay

Supports Virtual server

Supports DMZ functions

Supports two-level passwords and usernames

Supports WEB interface

Supports telnet CLI

Supports System status display

Supports PPP session PAP/CHAP

Supports IP filter function

Supports IP QoS function

Supports remote access control

Supports line connection status test

Supports remote management

（

Telnet; HTTP

）

Supports configuration file backup and restoration function

Ethernet supported such as Crossover Detection & Auto-Correction and polarity correction

Supports UPnP

Summary of Contents for W3100























































Search results

Summary of Contents for W3100

Reviews:

Related manuals for W3100

Brands by name

Popular brands

INNACOMM W3100, User Manual

Search results

Summary of Contents for W3100

Reviews:

Related manuals for W3100

Brands by name

Popular brands