background image

Inis Oirr MK2 Multifuel Boiler stove 

 

 

Chimney fire 

If the stove and chimney are kept 

clean, no fire should occur. If 

however it does happen, close the 

stove damper fully, close the stove 

doors tightly. Only once the fire in 

the stove and chimney has gone out 

should the stove be opened and the 

stove and chimney cleaned thoroughly. 

If the fire is substantial and doesn‟t 

extinguish, the fire brigade should be 

called. After a chimney fire, expert 

help should be sought to have the 

chimney examined for any damage before 

the stove is used again. 

Should you have an issue? 

In the event that you do have an issue 

that you aren‟t sure about please 

follow the following procedure. 

 

Firstly contact the installer 

and discuss the issue with them. 

 

If further help is needed please 

contact the retailer of the 

stove. We take pride in choosing 

retailers who have a proven 

track record in customer 

service. 

 

If we still have an issue that 

hasn‟t been resolved please 

contact the Inis Stoves 

technical department. Please 

have this manual with you when 

you call. 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Oirr MK2
















Reviews: