INIS Oirr MK2 User And Installation Manual Download Page 3

Inis Oirr MK2 Multifuel Boiler stove 

 

 

The stove has been designed for ease of 

use by the operation of only one air 

control knob. This adjustment knob is 

found on the left hand side of the stove 

and to increase the air turn clockwise 

and to close turn anti-clockwise. Your 

Inis Oirr MK2 boiler stove has a manual 

”Easy Start” damper fitted to the 

underside of the stove and the damper is 

operated as shown the diagram above by 

pulling the damper out away from the 

stove to open and pushing fully in 

towards the stove to close.  

To help with keeping the stove glass 

clean, load the fuel toward the back of 

the stove when lighting and fire the 

stove at a high rate and avoid prolonged 

periods at a very low setting. 

The Inis Oirr MK2 boiler stove is fitted 

with a multi-grate which facilitates the 

combustion of various fuels. The multi-

grate can also be riddled with the doors  

closed for cleanliness and safety. To 

achieve this use the riddling/ash pan 

removal tool as shown above. 

 

First firing 

When the stove is used for the first 

number of times the process of curing the 

paint will occur. To do this a small fire 

using only kindling wood should be lit 

for approximately 30 minutes, allow the 

stove to cool slightly then repeat the 

small fire using only kindling wood for 

another 30 minutes. The final action to 

cure the paint is to put on a strong fire 

before the stove has cooled down, at full 

output for at least one hour. The stove 

paint will emit fumes with are non-toxic 

but a window should be opened to avoid 

fume build up during the curing process. 

Before you operate the stove, consult 

with the installer that all the relevant 

work has been carried out correctly and 

that they have ignited a small fire in  

the stove and it is operating correctly. 

Check that all relevant local, national 

and European Standards have been adhered 

to when installing the stove.  

 

1.

 

Inis Stoves is dedicated to the 

principal of using renewable fuels 

in all our stoves. We recommend 

using wood fuel in the stove if 

possible. Some recommended fuels 

for this stove are below, 

A.

 

Hard or soft woods below 20%                                                              

moisture content, 

Eco friendly formed wood fuels 

for example “EcoBrix”. 

B.

 

Peat in solid form with low 

moisture content. 

C.

 

Solid fuels use only HETAS 

approved solid fuel, for example 

„EcoBrite‟ nugget form smokeless 

coal.  

 

 

2.

 

Never use liquid fuels in the stove 

3.

 

When in operation, the stove will 

be hot and care should be taken to 

avoid injury. 

4.

 

When using solid fuels like 

smokeless coal, the ash pan should 

be emptied at least every day. 

5.

 

Never attempt to modify the stove 

in any way and always use genuine 

Inis Stove spare parts. 

6.

 

Never place combustible or non-

combustible materials near, in or 

Summary of Contents for Oirr MK2
















Reviews: