18
EN
LIST OF COMPONENTS
fig. 1
A
Hood
B
Handrail
C
Storage basket
D
Rain cover (if available)
“SELF STANDING” SUPPORT
fig. 2
In order to allow the stroller to remain upright on
its own, pull out the support (
S1
) and place it in its housing.
OPENING THE STROLLER
fig. 3
To open the stroller, use the lever (
P1
) and
simultaneously press the release button (
P2
) until the control
device is released (
P
).
fig. 4
Holding the handle firmly on both sides, lift the
stroller until the correct opening click is heard.
Warning: before use, make sure that the stroller is
correctly opened by checking that the red area is no
longer visible from both sides.
Warning: act on the operating device (P) only during
the folding and unfolding activities on the stroller. Pay
attention not to operate accidentally this device during
normal use of the stroller.
REMOVING/ATTACHING THE FRONT WHEEL ASSEMBLY
In case of need, the front wheel assembly (
D
) can be easily
removed.
fig. 5
To remove it, pull it out from the front support
while holding down the lever (
D1
).
fig. 6
To reinstall it, simply position it and push it until it
clicks into place.
fig. 7
Caution: make sure that the wheels are properly
attached before use.
REMOVING/ATTACHING THE REAR WHEELS
Should it be necessary, the rear wheels (
E
) can easily be
removed.
fig. 8
Use a screwdriver (or similar tool, not included) to
operate the lever (
E1
) and simultaneously pull them out from
the rear support.
fig. 9
To reinstall them, simply position them and push
them until they click into place.
fig. 10
Caution: make sure that the wheels are properly
attached before use.
REAR WHEELS BRAKE
fig. 11
To operate the brake, use the rear central lever (
P3
).
Always engage the brake during stops.
BLOCKING/UNBLOCKING THE FRONT WHEELS
fig. 12
The stroller features swivelling wheels that can be
blocked or unblocked simply by operating the lever (
P4
) by
the front wheel assemblies.
HANDRAIL
fig. 13
The bumper bar (
B
) can be opened on one side
or completely removed; to open it, pull the lever (
B1
) and
remove it from its housing.
To remove it, repeat the operation on the other side as well.
Warning: never attach the bumper bar in the direction
opposite the one shown.
ADJUSTING THE BACKREST
fig. 14
To lower the backrest, release the rear strap by
pressing the button (
P5
) on the central device (
P6
).
fig. 15
To lift the backrest, press the button (
P5
) on the
control device (
P6
) and simultaneously pull the rear ring (
P7
).
SAFETY BELTS
fig. 16
Make sure that the back strap is properly inserted
in the ends of the waist one (
P10
).
fig. 17
Fasten the ends of the waist belt to the central
buckle (
P11
).
fig. 18
Always use the crotch strap (
P12
) in combination
with the waist strap, making sure that they are all well
adjusted around the baby.
Caution! Failure to comply with this precaution can cause
the baby to fall or slide out, with serious injury risks.
Caution: adapt the height and the length of the harness
according to the baby’s growth.
HOOD
fig. 19
To adjust the hood, simply accompany it to the
desired position.
fig. 20
The hood features a fabric insert that extends the
degree of cover, improving protection from the sun.
HOOD VENTILATION
The back of the hood can be removed and completely folded
down to allow for greater air circulation.
fig. 21
Detach the fixing velcro (
A1
) and wrap the hood
back, locking it with the small central buckle (
A2
).
REMOVING THE HOOD
fig. 22
To remove the hood (
A
), detach the fixing velcros
(
A1
).
fig. 23
Press the lever (
A3
) on the central joint (
A4
) and
simultaneously remove the hood from the housings (
A5
) on
the stroller.
INSTRUCTIONS
j
T
and dry it afterwards in order to remove sand and salt as they
may cause rusting.
• Clean the plastic and metal parts with a damp cloth or with
a mild detergent; do not use solvents, ammonia or benzine.
• Carefully dry metal parts after any contact with water to
prevent the formation of rust.
• Keep all moving parts clean and, if necessary, lubricate
them with light oil.
HINTS FOR CLEANING THE TEXTILE LINING
• Seat cover and harness are surface wash only. Clean with a
damp cloth and mild soap; do not use solvents, ammonia or
bleach.
Do not use abrasive cleaners or scrubbing pads.
• Follow the lining washing instructions on the labels.
Do not bleach
Do not tumble dry
Dry flat in shade
Do not iron
Do not dry clean
Do not spin-dry
• Dry the textile lining completely before using or storing it.
Summary of Contents for Quid
