background image

Ingeteam Power Technology, S.A.

www.ingeteam.com

Ingeteam Power Technology, S.A. 

Energy

 

Avda. Ciudad de la Innovación, 13 

31621 SARRIGUREN (Navarra) - Spain 

Tel.: +34 948 28 80 00 

Fax.: +34 948 28 80 01 

e-mail: [email protected]

Ingeteam S.r.l.

 

Via Emilia Ponente, 232 

48014 CASTEL BOLOGNESE (RA) - Italy 

Tel.: +39 0546 651 490 

Fax: +39 054 665 5391 

e-mail: [email protected]

Ingeteam GmbH

 

DE-153762639 

Herzog-Heinrich-Str. 10 

80336 MUNICH - Germany 

Tel.: +49 89 99 65 38 0 

Fax.: +49 89 99 65 38 99 

e-mail: [email protected]

Ingeteam SAS

 

Parc Innopole 

BP 87635 - 3 rue Carmin - Le Naurouze B5 

F- 31676 Toulouse Labège cedex - France 

Tel: +33 (0)5 61 25 00 00 

Fax: +33 (0)5 61 25 00 11 

e-mail: [email protected]

Ingeteam INC.

 

5201 Great American Parkway, Suite 320 

SANTA CLARA, CA 95054 - USA 

Tel.: +1 (415) 450 1869 

+1 (415) 450 1870 

Fax.: +1 (408) 824 1327 

e-mail: [email protected]

Ingeteam INC

3550 W. Canal St. 

Milwaukee, WI 53208 - USA 

Tel.: +1 (414) 934 4100 

Fax.: +1 (414) 342 0736 

e-mail: [email protected]

Ingeteam, a.s.

 

Technologická 371/1 

70800 OSTRAVA - PUSTKOVEC 

Czech Republic 

Tel.: +420 59 732 6800 

Fax.: +420 59 732 6899 

e-mail: [email protected]

Ingeteam Shanghai, Co. Ltd.

 

Shanghai Trade Square, 1105 

188 Si Ping Road 

200086 SHANGHAI - P.R. China 

Tel.. +86 21 65 07 76 36 

Fax.: +86 21 65 07 76 38 

e-mail: [email protected]

Ingeteam Ltda.

 

Rua Luiz Carlos Brunello, 286 

Chácara Sao Bento 

13278-074 VALINHOS SP - Brazil 

Tel.: +55 19 3037 3773 

Fax.: +55 19 3037 3774 

e-mail: [email protected]

AAY2000IKI06_ 
02/2012

Summary of Contents for Ingecon mWind Interface





































Reviews: