manualshive.com logo in svg

Ingersoll-Rand EP 60, Operators/Instruction Manual Options

Share
Download
Ingersoll-Rand EP 60 Operators/Instruction Manual Options Download Page 21

19

3.4  PUSH BUTTONS (Continued)

DISPLAY SELECT

Pressing this button will change the information
selected for the display. The display table will be
incremented. If the button is held, this display table
will scroll. This button can also be used to exit the
set point procedure.

NOTE: For readings less than 1 hr., hourmeter 
displays minutes. After 1 hr. the hourmeter displays
hours.

SET

The SET button is used to enter the set point
procedure. The set button is also used to reset
warnings and alarms. Pressing this button once will
reset a warning, twice will clear an alarm.

ARROWS

These buttons have several functions. If the
Intellisys is in the set point mode, the ARROWS are
used to change the set point values. If the unit has
multiple alarms or warnings, the ARROWS are used
to scroll through these conditions. The ARROWS
have a function in the calibration routine, which will
be described later.

PRESSURE SENSOR CALIBRATION (ZEROING)
ROUTINE

This routine is entered if the unit is not running and
both the up and down arrows button are pressed at
the same time. Make sure all pressure is relieved
from the compressor before calibration. The display
will flash the message “CALIBRATING”. After
calibration is completed the display will indicate
“READY TO START”. Zeroing should only be done
after a pressure sensor has been replaced or any
controller change.

DISPLAY

SELECT

SET

Summary of Contents for EP 60































































Reviews:

No comments

Brands by name

Popular brands

Load more brands