Ingersoll-Rand EP 60 Operators/Instruction Manual Options Download Page 10

Page: 10 / 62

WARNING

Hazardous voltage. Can cause
severe injury or death.

Only use factory supplied inlet for
incoming power. See Operators/
Instruction manual.

INGERSOLLrAND

NOTICE

Compressor is equipped
with power outage restart
option and will
automatically restart within
10-120 seconds after horn
sounds.

INGERSOLLrAND

Electrical power inlet.

NOTICE

INGERSOLLrAND

WARNING

Hazardous voltage. Can cause
severe injury or death.

Disconnect power before servicing.
Lockout/Tagout machine.

INGERSOLLrAND

WARNING

This machine is remote
start and stop equipped.

May start or stop at
any time.

Can cause severe injury or
death.

Disconnect power before
servicing.

Lock and tag out.

See Operators / Instruction
Manual.

INGERSOLLrAND

39543764

39540174

39543764

39540174

39899950

39541354

39547708

39584529

WARNING

Moving parts.
Can cause severe injury.

Do not operate with covers removed.
Service only with machine blocked to
prevent turn over.

INGERSOLLrAND

39540224

Summary of Contents for EP 60































































Search results

Summary of Contents for EP 60

Reviews:

Brands by name

Popular brands

Ingersoll-Rand EP 60, Operators/Instruction Manual Options

Search results

Summary of Contents for EP 60

Reviews:

Brands by name

Popular brands