manualshive.com logo in svg

Infranet Technologies M2M CONTROL CX320, Technical Manual

Share
Download
Infranet Technologies M2M CONTROL CX320 Technical Manual Download Page 26

 M2M Control CX320  Technical Manual V1.01

 

 

 

 

Page 26 of 42 

 

 
The network status and the battery level are indicated with different icons and level indicators.  
 
The following table describes the status of the cellular network: 
 
Status 

Icon 

Cellular off 

 

Cellular on 

 

Cellular on and connected 

 

Data connection over 2G or 3G 

 

Data connection over LTE 

 

 
The cellular signal level is indicated with 4 bars – also known from many mobile phones. One bar 
means low signal strength, and four bars represent high signal strength. No signal strength bars 
indicate that the cellular interface is powered up but is not connected to the network. 
 
Similarly, the battery level is indicated with six levels: the fully charged battery icon means fully 
charged, and the empty battery icon means low battery level. While charging the battery, the battery 
icon is animated to show the charging progress. 
Status 

Icon 

Battery level 

 

 
 
If LAN is enabled, the upper icon will switch between cellular status and LAN status.  
The following table describes the status of the LAN interface: 
 
Status 

Icon 

Not connected 

 

Connected 

 

 
If the M2M Control Communication Hub (formerly: M2M Control GPRS Gateway) is enabled, the 
lower icon will switch between the battery status and RCH status. 
 

 

Summary of Contents for M2M CONTROL CX320











































Reviews:

No comments

Brands by name

Popular brands

Load more brands