NOTE:
When you apply power to the inverters by pulling out the “E-Stop” if there is any motion on
the platform, immediately press “E-Stop” back in. Wait several seconds and try again if “OK” go
to next step.
3.) Pull out “E-Stop” all the legends n the window should highlight and all axes must have the
“START” icons highlighted. If not immediately press on the respective “STOP” icon to
close that axes. Also ensure that the
OFF
brake icon is highlighted under each axes except
counterweight.
NOTE: All axes movement of the motion platform is monitored by you sitting inside the
machine/cockpit facing forwards.
2-4A Lift Axis
1. To raise the platform, click on the left
RAISE
icon, the machine will slowly raise to the top.
2. Monitor the current value. As soon as it starts to rise sharply press “STOP” icon.
3.
To lower the platform, click on right
LOWER
icon and the platform will slowly descend.
4. Monitor the current value. As soon as it starts to rise sharply, press “STOP” icon.
NOTE:
The platform can be stopped at any point along the lift axis. However, you must not command any
other axes motion unless the platform is all the way at the top.
WARNING: THE PLATFORM MUST BE ALL THE WAY AT THE TOP BEFORE RUNNING
EITHER ROLL OR PITCH MOTION.
2-4B Roll Axis
NOTE!!!! Motion as seen sitting in the machine facing forward.
1. Click
on
RIGHT
icon, the machine will roll clockwise (+) direction, it will continue to roll until you
command “STOP”
2.
Hit “STOP” before commanding rotation in opposite direction
3. Click
LEFT
icon, the machine will roll counter-clockwise (-) until you hit stop.
4.
Hit “STOP” before commanding rotation in opposite direction.
2-4C Pitch Axis
1. Click on left
DOWN
icon, the machine will PITCH DWN (-) direction, it will continue until you
command “STOP”
2. Click on “STOP”
3. Click on right
UP
icon, the machine Pitch UP (+) direction.
Hit “STOP” before commanding rotation in opposite direction
2-4D Counterweight Motor
1. Click
on
DECREASE
icon, weight will move towards the center. Hit “STOP” before
going the other way.
2. Click
on
INCREASE
icon, weight will move away from the center.
2-4E Confirm Direction of Motor Movement
The correct direction of motion on the motion platform using the Mitsubishi Inverter control
program buttons is as follows:
Direction of rotation is referenced you sitting in cockpit seat.
1. PITCH:
DOWN
unit moves (nose-down),
UP
unit moves (nose-up)
2. ROLL:
RIGHT
unit moves clockwise,
LEFT
unit moves counter-clockwise.
3. LIFT:
RAISE
unit moves upwards,
LOWER
unit moves down .
4. Counterweight
DECREASE
moves weight toward weldment,
INCREASE
moves weight
away from center.
Summary of Contents for MaxFlight MT3000B ELECTRIC
