background image

Delta Treatment Systems • 9125 Comar Drive, Walker, LA 70785 • 1-800-219-9183 • www.deltatreatment.com

5

INTRODUCTION

Do not discard the following into the system:

• Paints, household chemicals, automobile fluids, mop water, etc. 

• Nonbiodegradable items such as cleaning wipes, cigarette 

butts, disposable diapers, feminine hygiene products, 

condoms, coffee grounds, rags, paper towels, bandages, 

latex, plastic or metallic objects. 

• Strong disinfectants or bleaches. Laundry products such as 

Lysol, Pine-Sol, Tidy Bowl, or discharge from water softeners. 

• Septic systems additives – they do more harm than good. 

• Excessive water from other sources as this can result in 

hydraulic overload. 

• Home brewery waste, strong medicines, antibiotics and 

antibacterial soaps should be avoided. 

Recommended detergents should contain low-sudsing, low 

phosphates and biodegradable ingredients. Fabric softener 

dryer sheets are recommended. 

Recommended cleaning products should be biodegradable 

and nontoxic such as Ivory & Sunlight dish washing liquids, 

Cascade & Sunlight powdered dishwasher detergents, Comet & 

Biz powdered cleaners, and baking soda.

SYSTEMS REQUIRING PUMPOUTS DUE TO THE ABOVE 

VIOLATIONS ARE NOT COVERED BY THE WARRANTY. 

The ECOPOD-N Fixed Film Wastewater Treatment System is 

designed to handle domestic wastewater; nothing else should 

go into it. For anything other than domestic wastewater, contact 

Delta Treatment Systems.

SAFETY WARNINGS 

 

 

The proper operation of this or any other home sewage 

system depends upon proper organic loading and the 

life of the microorganisms inside the system. Delta is not 

responsible for the in-field operation of a system, other 

than the mechanical and structural workings of the plant 

itself. Delta cannot control the amount of harsh chemicals 

or other harmful substances that may be discharged into 

the system by the occupants of a household; we can only 

provide a comprehensive owner’s manual that outlines 

substances that should be kept out of the system. 

Hydraulic overloading (flows in excess of design flow) may 

cause the sewage treatment system not to perform to the 

fullest capabilities. 

Ants have been shown to be destructive to the air pump. 

Regular care should be taken to prevent infestation of ants 

near the system. Damage or destruction by ants is not 

covered under manufacturer’s warranty. 

Your state or local health department may require 

other pieces of equipment to function separately or 

in conjunction with equipment manufactured by Delta 

Treatment Systems. Delta is not responsible for the 

Mechanical or electrical safety of equipment it does not 

manufacture or supply with its fixed film wastewater 

treatment system. Care should be used In evaluating the 

electrical or mechanical safety of equipment manufactured 

by others. This may include but is not limited to electrical 

control panels or air pumps. If electrical service has not 

been installed for checking air distribution system during 

installation, and if an extension cord is used to test the air 

pump, never leave the extension cord plugged in. Remove 

it after testing is completed.

DUE TO A POSSIBLE FIRE HAZARD, DO NOT PLUG 

INTO SERVICE EQUIPMENT ON POWER POLE AND DO 

NOT USE EXTENSION CORDS. ALL ELECTRICAL WORK 

PERFORMED BY THE INSTALLER OR OTHERS MUST BE IN 

ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE 

AND LOCAL CODES. 

SOLIDS REMOVAL  

The ECOPOD-N Fixed Film Wastewater Treatment System is 

designed to provide years of trouble-free operation. 

Determination of the need for solids removal can be done with a 

sludge judge sample. If the sludge judge indicates more than 12 

inches of sludge in the bottom of the reactor tank, the treatment 

plant should be pumped out. Call your local authorized sewage 

disposal service to have the tank contents pumped out and 

disposed of properly. 

 Pumping Method 

• The air pump should be in the off position.

• Remove all of the solids from both the reactor tank and 

primary tank. 

• After the pump out process is complete, fill the tank with fresh 

water to normal operating level.

• Refer to the “Installation Procedure” to get the treatment plant 

back into operation. 

• Should indication of improper operation be observed at any 

time, contact your local authorized Delta dealer/distributor. 

NOTE: THE COST ASSOCIATED WITH PUMPING THE 

TREATMENT SYSTEM IS NOT COVERED UNDER WARRANTY 

AND IS NOT INCLUDED IN THE SERVICE POLICY. 

SEASONAL USE GUIDELINES OF ECOPOD-N 

FIXED FILM WASTEWATER TREATMENT 

SYSTEM

These guidelines are for conditions as outlined below and apply 

for systems that are not in use for periods of time indicated. 

Site conditions not covered by the following must be forwarded 

to Delta for recommended guidelines to meet the particular site 
conditions.

1. System not in use for more than one month and less than 

three months. Electrical power is left on and there are no 

frost conditions.

  • 

Leave air pump on and system running

.

Summary of Contents for Delta ECOPOD E100N





























Reviews: