background image

 

WL100

 Manual                                                                     Page 37                                                                      Revision: 1‐14‐2019 

PRE‐INSTALLATION PROCEDURES 

 

      DANGER!

 

 

ELECTRICAL SHOCK HAZARD.  

Only qualified personnel who have read and understand this entire manual should attempt to 
install, or service this unit, failure to do so could result in death or serious injury.  DO NOT plug 
into an electrical supply until specifically instructed.  
 
Red Compressor/Heater Switch must be in the O=OFF position while the Hot 
Tank is empty.  Damage could occur within one minute and the two Hot Tank 
Overload Devices (High Safety Limit) require manual reset if heater is turned 
on with an empty Hot Tank.  
 

 

 

       WARNING!

  

ALWAYS SANITIZE BEFORE USE. 

 Sanitize before use to eliminate any potential microbiological contaminates.      

 

CAUTION!

  

DRIP TRAY DRAIN.

  

If you intend to provide a drip tray drain for your customer, be aware that 
you will be called multiple times per month to service and unclog the tubing 
leading away from the drip tray to drain.  Users will clog the drain with 
paper clips, erasers, napkins, tea bags, gum, and various other intended 
items.  Waterlogic recommends you establish a minimum of weekly visits to 
the machine for cleaning of the drip tray drain. 

Materials Needed:  

 

Personal Protective Equipment.  Rubber or Nitrile Safety Gloves and Protective Eyewear  

 

Phillips Screwdriver   

 

Temperature Gauge 

 

Water Pitcher or Container to collect water from the faucet 

 

19 Liter (5 gallon) container or drain basin 

 

Sanitizer ‐ Household Bleach (5.25% Sodium Hypochlorite) or Citric Acid Based Cleaner 

 

¼” Plastic Tubing, at least 1.25 meters (4 feet) in length, and assorted ¼” quick connect 
fittings 

 

TDS Meter and Test Strips for measuring chlorine – Optional 

 

Sanitizing Cartridge – an empty Waterlogic Filter with the cartridge removed 

 

1.

 

Unpack the 

Waterlogic WL100 Water Treatment System 

and check exterior for damage.

 

 

  

 

Sanitizing 

 
Sanitize using a Household Bleach (5.25% Sodium Hypochlorite solution) or another approved 
cleaner throughout the cold‐water circuit.  Follow all instructions on the sanitizer and flush with 
fresh water through the faucet until odor and taste is acceptable. 

 

       WARNING!  

USE PROPER PERSONAL PROTECTIVE EQUIPMENT

 

Summary of Contents for WL100











Reviews: