Inficon Southern Cross IRwin Quick Start Manual Download

Page: 25 / 25

No.

Message

Possible error sources

Remedy

E17

"Gas Sensors" has red
cross in function test
result screen.

Sensor error or warm-up
drift

Restart detector.
If problems remains: Contact INFICON service.

E18

"Buzzer" has red cross
in function test result
screen.

Buzzer "hole" blocked or
filled with water

Dry and clean buzzer hole.
Restart detector.
If problems remains: Contact INFICON service.

E19

"LED" has red cross in
function test result
screen.

LED broken

Contact INFICON service.

E20

RAM test error (Power
off)

Memory damaged or test
error

Restart detector.
If problems remains: Contact INFICON service.

E21

ROM test error (Power
off)

Memory damaged or test
error

Restart detector.
If problems remains: Contact INFICON service.

E22

CRC error (power off)

Memory damaged or test
error

Restart detector.
If problems remains: Contact INFICON service.

E23

"Gas Sensors" has red
cross in function test
result screen.

Sensor error or warm-up
drift

Restart detector.
If problems remains: Contact INFICON service.

E24

No message given

Service info only

No action needed.

E25

Surrounding
temperature is outside
of rated temperature.
Function might be
affected

Instrument temperature is
too high or to low

Explosion protection cannot be guaranteed.
Immediately move detector to cooler place or
switch OFF if flammable gases could be present.

Summary of Contents for Southern Cross IRwin


























Search results

Summary of Contents for Southern Cross IRwin

Reviews:

Related manuals for Southern Cross IRwin

Brands by name

Popular brands

Inficon Southern Cross IRwin, Quick Start Manual

Search results

Summary of Contents for Southern Cross IRwin

Reviews:

Related manuals for Southern Cross IRwin

Brands by name

Popular brands