manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Operating Manual

Share
Download
Inficon Sensistor ISH2000 HySpeed Operating Manual Download Page 6

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

6

OM-Sensistor ISH2000-EN-201304

EN

1

User information

Read this user manual carefully before using the Sensistor ISH2000.

1.1   Notes and safety notices

This manual contains warnings and cautions concerning the safe use of the product. 
See definitions below.

Note: A Note is used to indicate information that is important for trouble-free and optimal 

use of the Sensistor ISH2000.

1.2   Document outline

The document is divided in two main parts:
•

Getting started

•

Reference section

The Getting started part consists of step by step case examples, explaining how to use 
the Sensistor ISH2000 in a variety common situations. The Reference section consists of 
in depth explanation and additional information, which completes the user manual 
with all relevant information.

1.3   Conventions used in this book

In this user manual the following text style (

hardware command

) is used for references 

to hardware commands or button labels, while this text style (

software command

) is 

used for references to software commands and menu choices.

WARNING!

Warning indicates a hazardous situation which, if not 
avoided, could result in death or serious injury. It is 
important not to proceed until all stated conditions 
are met and clearly understood.

CAUTION!

Caution indicates a hazardous situation which, if not 
avoided, could result in minor or moderate injury. It is 
important not to proceed until all stated conditions 
are met and clearly understood.

NOTICE!

Notice indicates instructions that must be 
followed to avoid damage to the Sensistor 
ISH2000 or other equipment.

Summary of Contents for Sensistor ISH2000 HySpeed



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands