manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Operating Manual

Share
Download
Inficon Sensistor ISH2000 HySpeed Operating Manual Download Page 45

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

 

OM-Sensistor ISH2000-EN-201304

45

EN

Note:

Remember to use capitals for the header.

APC driver installation

All standard APC drivers are installed in the detector.

Note:

Battery operated model Sensistor ISH2000 does not incorporate the APC 
feature.

For custom APC driver design and installation contact support at INFICON.

8.17   Sensistor ISH2000P installation

The panel mount model can be installed in the operator’s panel or any other flat 
surface of your leak tester. Mounting brackets and panel rubber seal are delivered 
with the detector. Refer to Figure 8-6.

Fig 8-7. Panel cut out dimensions.

Measurements:
•

Panel cut out: 262 x 127 mm (5 x 10.3 inches).

•

Maximum panel thickness: 8 mm (0.3 inch).

•

Allow an extra 20 mm (0.8 inch) on left and right side for mounting brackets.

Depth of open space in panel is at least 15 cm (6 inches) for Sensistor ISH2000 to fit.

CAUTION!

The detector should preferably be mounted on a 
vertical surface. Tilting more than 30 degrees is not 
recommended. Tilting more makes air circulation 
poor resulting in increased temperature inside 
detector. This will reduce contrast of display and 
lifetime of lamp and electronic circuits.

NOTICE!

After installation verify that ambient 
temperature is below 50ºC.

Free space horisontally 
300 mm (12 inches)

262 mm (10.3 inches)

127 mm (5 inches)

Free space vertically 
140 mm (5.5 inches)

Summary of Contents for Sensistor ISH2000 HySpeed



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands