manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Operating Manual

Share
Download
Inficon Sensistor ISH2000 HySpeed Operating Manual Download Page 32

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

32

OM-Sensistor ISH2000-EN-201304

EN

Quick purging also enhances signal repeatability.

Note:

Purge level interrupts active sampling of APC probes. This means that higher 
signals will be underestimated as the sensor is purged before full signal has 
developed.

Reset Signal

Reset the sensor signal in Measuring mode and Locating mode.

8.10   Display Settings

This section describes the different display settings of the Sensistor ISH2000.

Contrast

Contrast level of display. Higher value gives higher contrast. The contrast may need 
adjustment if ambient temperature changes.

Brightness

Brightness of the display lamp. 

Invert Colors

Change the black to white and white to black. Useful in a dark environment to keep 
a high readability.

Screen Save Timeout

Display lamp will turn off if instrument is left idle for the number of minutes set by 
this parameter. The screen save timeout can be set between 1 and 60 minutes, the 
function is deactivated if set to OFF. The display lamp will return to the set 
brightness if any of the display or probe buttons are pressed, if a gas signal is 
detected or an instrument error is detected.

8.11   General Settings

This part describes the general settings of the Sensistor ISH2000.

Correlation Value

Correlation Value

 is used when it is necessary to correct the relation between the 

detector signal and the displayed number. This might be necessary if the hydrogen 
concentration of the Tracer Gas, inserted into the test object is changed, e.g. when 
the Tracer Gas is mixed with existing air in the test object

Language

The Sensistor ISH2000 user interface contains the following languages:
•

English

•

French

•

German

•

Italian

•

Spanish

•

Swedish

Summary of Contents for Sensistor ISH2000 HySpeed



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands