background image

4

GB

Find  a  large,  clean  area  to  assemble  your 

appliance. Please refer to the parts list and 

assembly diagram as necessary.

Please use protective gloves when assem-

bling this product.

To  avoid  losing  any  small  component  or 

hardware, assemble your product on a hard 

level  surface  that  does  not  have  cracks  or 

openings.

To avoid damage to soft floor or carpet, do 

not assemble or move the appliance on soft 

floor or carpet.

Follow  all  steps  in  order  to  properly 

assemble your product.

Make  sure  all  the  plastic  protection  rip  off 

before assembling.

Do not force parts together as this can result 

in personal injury or damage to the product.

When applicable,  tighten all hardware con-

nections by hand first, once the step is com-

pleted, go back and full tighten all hardware.
Caution:  Whilst  every  effort  has  made  in 

manufacture  of  your  appliance  to  remove 

any sharp edge, you should handle all com-

ponents with care to avoid accidental injury.

Time to assemble

                    

Number of people required to assemble

One people

Assembly instructions

10 minutes

Summary of Contents for SRPH67

















Reviews: