background image

2

WARNING

1.  For  use  outdoors  or  in  amply  ventilated 

areas.

2. An amply ventilated area must have a mini-

mum of 25% of the surface area open.

3. The surface area is the sum of the walls 

surface.

4.  This  appliance  is  not  fitted  with  “Atmo-

sphere sensing device”.

WARNING:

  Read  the  instructions  before 

installation and use.

Warning: 

This  appliance  must  be  installed 

and  the  gas  cylinder  stored  in  accordance 

with the regulations in force.

Warning: 

Use only the type of gas and the 

type  of  cylinder  specified  by  the  manufac-

turer.

Warning:

  Do  not  obstruct  the  ventilation 

holes of the cylinder housing.

Warning: 

In  case  of  violent  wind  particular 

attention must be taken against tilting of the 

appliance.

Warning: 

Do not move the appliance when in 

operation.

Warning:

 Shut off the valve at the gas cylin-

der or the regulator before moving the appli-

ance.

Warning:

  The 

Warning:

  The heater can’t be used when the 

 

tubing  or  the  flexible  hose 

must be changed within the prescribed inter-

vals.

GB

heat exchange tube is retracted into cylinder 

compartment.

WARNING: 

The  use  of  this  appliance  in 

enclosed  areas  can  be  dangerous  and  is 

PROHIBITED.

Warning:

  Do NOT keep the heater fully 

 

extended and the heat exchange tube must be

lowered down to position during transportation!

Summary of Contents for SRPH67

















Reviews: