background image

10

Cleaning and maintenance

To enjoy years of outstanding performance 

from your heater make sure you perform the 

following maintenance activities on a regular 

basis:

● Keep exterior surfaces clean.

 Use warm soapy water for 

cleaning.

 Never 

use flammable or corrosive cleaning agents.

 While washing your unit, be sure to keep 

the area around the burner and pilot assem-

bly  dry  at  all 

times.

  If  the  gas  control  is 

exposed

 to water in any way, do NOT try to 

use it. It must be replaced.

 Air flow must not be 

obstructed.

 

Keep

 con-

trols,  burner,  and  circulating  air  passage-

ways 

clean.

  Signs  of  possible  blockage 

include:

Gas  odor  with 

extreme

  yellow  tipping  of 

flame.

Appliance does NOT reach the desired tem-

perature.

Appliance glow is excessively uneven.

Appliance makes popping noises.

  Spiders  and  insects  nest  in  burner  or 

orifices.

  This  dangerous  condition  can 

damage heater and render it unsafe for 

use. 

Clean  burner  holes  by  using  a  heavy-duty 

pipe 

cleaner.

 Compressed air may help clear 

away small particles.

 Carbon deposits may create a fire 

hazard. 

Clean heat reflector  with  warm  

  soapy  

  water  

if any carbon deposits develop.

GB

Check  the  tubing  or  the 

flexible

  hose  (at 

least  once  per  month  and  each  time  the 

cylinder  is 

changed).

  If  it  shows  signs  of 

cracking,  splitting  or  other  deterioration,  it 

must  be 

exchanged

  for  a  new  hose  of  the 

same length and of the equivalent quality.

STORAGE

Between uses:

● Turn the control knob to OFF position.

● Turn LPG cylinder to OFF position.

  Store appliance upright in an area 

sheltered from direct contact with inclement 

weather (such as rain, sleet, hail, snow, dust

and debris).

 If desired, cover appliance to protect 

exterior surfaces and to help prevent debris 

in air passages.

During  periods  of  extended  inactivity  or 

when NOTE transporting;

 Turn the control knob to 

OFF

 position (full 

disk). before covering.

 Disconnect 

LPG

 Cylinder and move to a 

secure,  well-ventilated  location 

outdoors. 

DO NOT store in a location that will 

exceed 

50 °C.

  The 

LPG

  cylinder  must  be  kept  out  of 

reach  of  children,  and  not  in  a  building, 

garage or any other enclosed area.

  Store 

 

Remove safety screws. Remove knob from 

Keep gas chamber door partially open. Turn

control panel and store in door.

 

appliance  upright  in  an  area  shel-

tered  from  direct  contact  with  inclement 

weather (such as rain, sleet, hail, snow, dust 

and debris).

●Always

 remove the battery from the patio 

flare if not being used for long periods of time 

as  battery  leakage  can  cause  corrosion  in 

the battery ignition housing.

 If desired, cover appliance to protect 

exte

-

rior surfaces and to help prevent debris in air 

passages.

NOTE

Wait until appliance is cool before 

covering.

Slowly descend heat exchange tube.

heat exchange tube clockwise.

Summary of Contents for SRPH67

















Reviews: