Indexa 1000 R Installation And Operating Instructions Manual Download Page 16 | Manualshive

Page: 16 / 16

background image

System1000_GB_130705.doc

Page

16

22. Drilling Template

-

Hold the template to the mounting position, and check that it is horizontal.

-

Mark the positions for the fixing holes.

-

Remember that the casing of the siren is bigger than the template!

-

The anti-tamper spring must be positioned on the same level as the back of the

casing, otherwise the siren will sound.

WARNING:

If the anti-tamper switch is enabled, do not take the siren off the wall after the anti-

tamper spring is depressed. If the siren sounds, press the OFF button on the keyfob to

silence the alarm.

Indexa GmbH Paul-Böhringer-Str. 3 D – 74229 Oedheim

position of the

anti-tamper spring

«
...
14
15
16

Summary of Contents for 1000 R

















Reviews:

No comments

Related manuals for 1000 R

Brand: Nelsen Corporation Pages: 16

Brand: National Instruments Pages: 34

Brand: Ransburg Pages: 49

Brand: Balboa Pages: 2

Brand: Badger Meter Pages: 20

Brand: Eaton Pages: 12

Brand: fakro Pages: 16

Brand: e-BLEACH Pages: 24

Brand: J3C Pages: 2

Brand: Hanna Instruments Pages: 88

Brand: Saftronics Pages: 13

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: Casambi Pages: 2

Brand: V2 Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands