background image

2. Safety
 

2.1 Safety Alert Symbol And Signal Words

You must read, understand and follow the instructions

given by the operating unit manufacturers, as well as

the instructions in this manual.

The safety information in this manual is denoted by the

safety alert symbol:

This symbol means ATTENTION! BECOME ALERT!

YOUR SAFETY IS INVOLVED!

The level of risk is indicated by the following signal

words:

2.2 Operational Hazards

Carefully read all safety messages in this manual and

on equipment safety signs. Keep safety signs in good

condition and replace missing or damaged safety

signs.

New equipment components and repair parts must

include the current safety decal.

Learn how to properly operate equipment. NEVER

operate or work around this equipment without proper

instruction, while fatigued or under the influence of

alcohol, prescription or non-prescription medication or

if feeling ill.

Keep your equipment in proper working condition.

Know the regulations and laws that apply to you and your

industry. This manual is not to replace any regulations

or laws. Additional information may be found at:

www.nfpa.org or www.osha.gov.

If you do not understand any part of this manual, contact

Imperial Systems, Inc. at 724-662-2801.

imperialsystemsinc.com 

    

 

   Imperial 

Systems 

Inc.

DANGER

DANGER - Indicates a hazardous situation,

which, if not avoided, WILL result in death

or serious injury.

WARNING

WARNING - Indicates a hazardous

situation, which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION - Indicates a hazardous situation,

which, if not avoided, could result in minor

or moderate injury.

NOTICE

NOTICE - Indicates a situation that could

result in damage to the equipment 

or other property.

WARNING

Prevent serious injury or death.

Read and understand this manual before

operating equipment.

WARNING

Prevent serious injury or death 

from moving parts.

Moving parts can crush and dismember.

Do not operate without guards 

and shields in place.

Disconnect and lockout power source

before adjusting or servicing.

Summary of Contents for CMAXX





























Reviews: