background image

7. STARTUP

1. Check all hardware to make sure it is tight, and all duct connections 

are sealed properly.

2. Check that filters are installed properly and that all lift rails are in 

up position.

3. Check that compressed air is on and regulated to 80 PSI 

(Recommend using a minimum of 1 in. diameter pipe to plumb the 

compressed air to the CMAXX).

4. Check that timer controller is on and properly programmed. See 

section 6 for programming instructions. The following settings work 

well in most applications.

 

• Last output: This number needs to match number of 

 

   diaphragm valves on CMAXX.

 

• Time Off: 10 Seconds.

 

• Time On: 150 Milliseconds.

 

• High Limit: 3.0 INWC.

 

• Low Limit: 2 INWC.

 

• High Alarm: 6.0 INWC.

 

• Low Alarm: 0.0 INWC.

 

• Cycle Delay: 0 Minutes.

 

• Down Time Cycles: 5 Minutes.

 

• Auto Alarm Reset: 5 Seconds.

5. Set timer controller to continuous and verify that diaphragm valves 

pulse properly. You should hear a short pulse of air every 10 seconds in 

the dust collector.

6. Set timer controller to on demand for normal operation.

7. Verify that pressure ports on body of CMAXX are plumbed to timer 

controller.

8. If using a drum kit with slide gate, make sure slide gate is open and 

drum is connected and sealed. Hopper on CMAXX is not intended to 

store material in it.

9. Set fan outlet damper to 75% open.

10. Bump start fan and verify wheel is rotating in proper direction.

11. Start fan and allow to reach full operating speed. Check AMP draw. 

Fan should be operating below full load amp rating on motor name 

plate. If operating above full load amps, gradually close fan outlet 

damper until amps drop below full load amps value.

12. It is recommended that air readings are taken at startup and the 

fan outlet damper adjusted to match rated CFM of your dust collector. 

A dust collector operating above the design CFM will experience 

reduced filter life.

13. Imperial Systems, Inc. does offer a system startup service. Please 

contact your sales representative for current pricing for this service.

imperialsystemsinc.com 

    

 

16 

   Imperial 

Systems 

Inc.

NOTICE

Operating dust collector above the design

CFM will reduce filter life.

Summary of Contents for CMAXX





























Reviews: