8
SET YOUR MIN AND MAX HEIGHT LIMITS
If you have shelves above your desk or a file cabinet below,
you may want to limit your desk’s adjustment range to avoid
any accidental collisions.
To set your maximum height limit:
1. Adjust the desk height to your desired position. It must
be within the upper half of the desk’s height adjustment
range (desk height > ~35 inches).
2. Press and hold up
▲
and down
▼
buttons together for
five seconds. When the controller beeps, your maximum
height limit is saved.
To set your minimum height limit:
1. Adjust the desk height to your desired position. It must
be within the lower half of the desk’s height adjustment
range (desk height < ~35 inches).
2. Press and hold up
▲
and down
▼
buttons together for
five seconds. When the controller beeps, your minimum
height limit is saved.
To deactivate a height limit:
1. Move your desk to the upper half of its height adjustment
range (desk height > ~35 inches) if you wish to deactivate
a maximum height limit. Or, if you wish to deactivate a
minimum height limit, move your desk to the lower half of
its height adjustment range (desk height < ~35 inches).
2. Press and hold both up
▲
and down
▼
buttons together
for five seconds. When the controller beeps, your height
limit is deactivated.
CHANGE DISPLAY BETWEEN IN & CM
You can change your controller’s height display between
centimeters and inches.
1. Press and hold ‘S’ button for five seconds to enter settings
menu.
2. Press up
▲
or down
▼
button to select ‘S-1’.
3. Press ‘S’ button once.
4. Press up
▲
or down
▼
button to select ‘0’ for display in
centimeters or ‘1’ for display in inches.
5. Press ‘S’ button again to finish setup.
LOCK OR UNLOCK THE CONTROLLER
When the controller is locked, height adjustment and settings
are disabled.
To lock:
1. Press and hold ‘S’ button and up
▲
button together for five
seconds.
2. Display shows ‘Loc’, which means the display is locked.
To unlock:
1. Press and hold ‘S’ button and down
▼
button together for
five seconds.
2. Display shows desk height, which means the display is
unlocked.
ADVANCED CONTROLLER OPTIONS
FINE-TUNE THE DISPLAY HEIGHT
Your ZipDesk height reading is already calibrated to default factory
configuration of a 0.75”-thick desktop and fully-closed leveling pads on
the feet. If for any reason your desk’s base height is changed, such as by
the addition of caster wheels, and you want to alter the height reading
up or down follow these instructions.
1. Press and hold ‘S’ button for five seconds to enter settings menu.
2. Press up
▲
or down
▼
button to select ‘S-5’.
3. Press ‘S’ button once.
4. Press up
▲
or down
▼
button to adjust the height displayed on
the controller.
5. Press ‘S’ button again to finish setup.
RESET CONTROLLER TO FACTORY SETTINGS
After factory reset, all saved settings will be restored to default values.
1. Press and hold the up
▲
and down
▼
buttons together for 10
seconds. The controller will beep once at 5 seconds and once again
at 10 seconds. Display shows ‘000’.
2. Press and hold the down
▼
button until the display shows the
height of the desk. Your controller is reset to factory settings.
ADJUST ANTI-COLLISION SENSITIVITY
Your desk is programmed to stop when it is sufficiently obstructed
during height adjustment. Your default anti-collision sensitivity is
set to level ‘2’. You can adjust your anti-collision sensitivity with the
following steps:
1. Press and hold ‘S’ button for five seconds to enter settings menu.
2. Press up
▲
or down
▼
button to select ‘S-4’ for downwards
movement, or ‘S-3’ for upwards movement. (Downwards and
upwards movement must be adjusted separately.)
3. Press ‘S’ button once.
4. Press up
▲
or down
▼
button to choose anti-collision sensitivity
(‘0’ = off, ‘1’ = least sensitive, ‘8’ = most sensitive).
5. Press the ‘S’ button once to finish setup.
ADJUST DESK TIPPING CONTROL SENSITIVITY
(G-SENSOR)
Your desk is programmed to stop if it begins to tip during height
adjustment. Your default desk tipping control sensitivity is set to ‘0’.
You can adjust your desk tipping control sensitivity with the following
steps:
1. Press and hold ‘S’ button for five seconds to enter settings menu.
2. Press up
▲
or down
▼
button to select ‘S-2’.
3. Press ‘S’ button once.
4. Press up
▲
or down
▼
button to choose sensitivity (‘0’ = off, ‘1’ =
least sensitive, ‘8’ = most sensitive). 5. Press the ‘S’ button once to
finish setup.
