background image

11

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

Boiler ignition

. Before ignition make sure the 

heating system is filled with water and that the 

manometer (7) indicates a pressure of 1 ÷ 1.2 bar.

- Open the gas cock upstream from the boiler.
- Press key (2) and set the boiler on Summer (

) or Winter ( ). 

 

N.B.:

 the button (2) must be pressed and 

held for the time required to switch from the 

Stand-by (  ), Summer (  ) or Winter (  ) 

function.

 

Attention:

 after each switch the button must 

in any case be released to switch to the next 

function.

When in summer position ( ) the domestic 

hot water temperature is adjusted with the but-

tons (3-4).
When the winter position is selected ( ) the 

system water temperature is adjusted with the 

buttons (5-6), whilst the domestic hot water 

temperature is adjusted using the buttons (3-4), 

by pressing (+) to increase and (-) to reduce the 

temperature.
From this moment the boiler functions auto-

matically. With no demand for heat (heating or 

domestic hot water production) the boiler goes 

to “standby” function, equivalent to the boiler 

being powered without presence of flame. Each 

time the boiler ignites, the relative flame present 

symbol is displayed (15).

2.5 TROUBLESHOOTING.

In the event of an anomaly the boiler backlight 

turns from green to red on and the relative error 

codes, listed in the table, flash on the display.

Anomaly signalled

code

error

No ignition block

01

Over-heating (safety) thermostat 

block

02

Flue safety thermostat anomaly

03

Electro-mechanical contacts

04

Flow probe anomaly

05

Insufficient system pressure

10

Parasite flame

20

Insufficient circulation

27

Loss of remote control commu-

nication

31

Ignition block.

 The boiler ignites automatically 

with each request for room heating or hot water 

production. If the burner does not ignite within 

10 seconds, the boiler goes into "ignition block" 

(code 01). To eliminate “ignition block” the Reset 

button (1) must be pressed. On commissioning 

or after extended appliance downtime, it may 

be necessary to eliminate the “ignition block”. If 

this phenomenon occurs frequently, contact an 

authorised company (e.g. Immergas After-Sales 

Technical Assistance Service).

Overheating thermostat block.

 During normal 

operation, if a fault causes excessive overheating 

internally, the boiler goes into overheating block 

(code 02). After allowing to cool, eliminate the 

"overheating block" by pressing the Reset key (1). 

If this phenomenon occurs frequently, contact an 

authorised company (e.g. Immergas After-Sales 

Technical Assistance Service).

Flue safety thermostat anomaly.

 If the flue 

evacuation pipe does not work properly during 

functioning, the flue thermostat intervenes by 

blocking the boiler (code 03). The boiler will 

automatically restart after 30 minutes if normal 

conditions resume without having to be reset. 

If the flue thermostat intervenes 3 times in less 

than two hours (code 03), it is necessary to reset 

the boiler manually by pressing the Reset button 

(1). If this anomaly persists, contact a qualified 

technician for assistance (e.g. Immergas After-

Sales Service).

Electro-mechanical contacts

 This occurs when 

the safety thermostat, the fume pressure switch or 

the system pressure switch do not work properly 

(code 04). The boiler does not start; try resetting 

the boiler. If the anomaly persists contact an 

authorised company (e.g. Immergas After-Sales 

Technical Assistance Service).

Delivery probe anomaly

 If the board detects an 

anomaly on the flow probe (code 05), the boiler 

will not start; contact an authorised company 

(e.g. Immergas After-Sales Technical Assistance 

Service).

Insufficient system pressure. 

Water pressure 

inside the heating system (code 10), sufficient to 

guarantee the correct functioning of the boiler, 

is not detected. Check that the system pressure 

is between 1÷1.2 bar.

Parasite flame.

 This occurs in the event of a leak 

on the detection circuit or anomaly in the flame 

control unit (code 20); try to reset the boiler. 

If the anomaly persists contact an authorised 

company (e.g. Immergas After-Sales Technical 

Assistance Service).

Insufficient water circulation. 

This occurs if 

the boiler overheats due to insufficient water 

circulating in the primary circuit (code 27); the 

causes can be:
- low system circulation; check that no shut-off 

devices are closed on the heating circuit and 

that the system is free of air (deaerated);

- pump blocked; free the pump.
If this phenomenon occurs frequently, contact an 

authorised company (e.g. Immergas After-Sales 

Technical Assistance Service).

Loss of Remote Control communication.

 This 

occurs 1 minute after loss of communication 

between the boiler and the remote control (code 

31). To reset the error code, remove and re-apply 

voltage to the boiler. If this phenomenon occurs 

frequently, contact an authorised company (e.g. 

Immergas After-Sales Technical Assistance 

Service).

Boiler shutdown.

 Press the button (2 Fig. 2-1) 

(

) until the symbol ( ) appears on the 

display.

N.B.:

 in these conditions the boiler is still 

powered.
Disconnect the external omnipolar boiler switch 

and close the gas cock upstream of the appliance. 

Never leave the boiler switched on if left unused 

for prolonged periods.

2.6  RESTORING CENTRAL HEATING 

SYSTEM PRESSURE.

Periodically check the system water pressure. 

The boiler manometer should read a pressure 

between 1 and 1.2 bar.

If the pressure is below 1 bar (with the circuit cool) 

restore normal pressure via the filling cock located 

in the lower part of the boiler (Fig. 2-2).

N.B.:

 close the filling cock after the operation.

If pressure values reach around 3 bar the safety 

valve may be activated.

In this case contact a professional technician 

for assistance.
In the event of frequent pressure drops, contact 

qualified staff for assistance to eliminate the pos-

sible system leakage.

2.7   SYSTEM DRAINING.

To drain the boiler, use the special draining 

valve (Fig. 2-2).

Before draining, ensure that the filling valve is 

closed.

Summary of Contents for NIKE MYTHOS 24 2 E

























Reviews: