TRADUCTION OF THE ORIGINAL USER INSTRUCTIONS
PERFECT 250-275-300eng ED.2010 rev.00
27/40
To make cuts between 45 deg. right and 45 deg. left it is necessary the following :
- no material on the work table or tighted in the vice.
- unlock the lever -pos.1/dr.RI0129 - by wheeling it towards the right .
- completely lower the reducer head ( at the end of the cut ) and wheel it by the handle supporting rod -
pos.4/dr.RI0128- until reading on the scale -pos.9/dr.RI0128- the required angle, then lock the lever-pos.1/dr.RI0129-
again.
On the model PERFECT 300, during thiese operations be sure that the anti-burr arm-pos.10/dr.RI0128 - and the
closing jaw -pos.11/dr.RI0128- do not interferes the blade cutting line, otherwise displace them by loosing
before the respective fixing screws .
- 15.5 - VICE ROTATION FOR OBLIQUE CUTS (ONLY FOR PERFECT 275 AND 300)
It is possible to make the same inclined cuts by wheeling the vice instead of the cutting unit ( only if : you are not cutting
too long pieces ).
To do this : loosen the grub screw -pos.6/dr.RI0128 - some turns, wheel the lever below to the base-pos.1/dr.RI0129 -
towards the right and wheel the the vice by keeping the reducer head up.
15.6 - OVERLOAD PROTECTIONS
The motor is protected against overheating by bi-metal thermo-protectors (placed directly inside the winding),
that stop the control circuit.
If you want to start again the machine, you have to wait that the temperature falls below the fixed limit of interventation,.
In the meantime try to remove the causes, that have brought to this overheating, for ex. the blade is locked in the
workpiece, the cutting speed is too high, the motor is in short circuit, an so on.
16 - ADJUSTMENTS ( disconnect machine from electrical supply )
VICE -
Only for PERFECT 300 : there is the possibility to adjust the locking force of the anti-burr arm-pos.10/dr.RI0128 - ( by
the screw-pos.12/dr.RI0128- that has to be unscrewed or screwed after loosening the screw-pos.2/dr.RI0130 ), in the
case that the cutpiece is not rightly teightened.
Summary of Contents for Perfect 250
