M880 ALL EN 2.7.2.docx
45/56
Current (4/20mA, 0/20mA)
Digital
0/24 VDC optoisolated
Outputs:(
4
)
ON/OFF 128 max:
Relay (AC e DC);
MOSFET (DC)
ANALOG 32 max
Proportional (PWM)
Analog (current)
Analog (voltage)
Serial communication interfaces:
RS232 or RS485 (115200 Baud max)
CAN_Bus (ID 11-29 bit)
CANOpen (ID 11-29 bit)
Other types on request
Power supply (AC type)
45-240Vac, max 1.1A@45Vac, 45VA
Power supply (AC/DC type )
11-30Vdc, max 4A@12Vdc, 44W /
24 Vac (50-60 Hz), max 2,8A , 68VA
Operating temperature range
-25°C to +70°C (-13°F to +158 °F)
Storage temperature range
-
40°C to +85°C (-40°F to +185 °F)
Housing material
UL94 V0 5VA, UL 746C (f1)
Casing protection degree
IP66
Dimensions
205x130x280
mm
(L.W.H.)
Weight (standard configuration)
3,5 Kg
Mounting brackets minimum load (
6
)
120N
NOTE(1):
The passive emergency intervention time rule is set to 500ms. On customer request, the installer can adjust it from
500 to 2000ms.
NOTE (2):
Both, the receiver and the diagnosis configurations can be made with an IMET-dedicated interface by radio link.
This technique is useful in all those cases when the receiver is not easily accessible, or when you do not want to open the case
to access the data port.
NOTA (3):
Inputs are managed by the user card SUH. The technical data can be found on the SUH’s data sheet.
NOTE (4): Electrical features of COMMANDS.
The number shown is the one managed by the logic board;
the real
number could be limited by physical constraints (i.e. on the mother board it is not possible to mount 4 DAC board
for 32 analog outputs)
NOTE (
5
):
For versions that do not contemplate the presence of the DAC board, it is possible to have a supply voltage having
an extended range
NOTE (
6
):
See section 4.2.10 of the
Directive
IEC 60950-1 2007-02 Wall or Ceiling Mounted Equipment
.
Output type
Command
type
# of outputs
AC specifications
DC specifications
SERVICE relay
board
(PCB201 / PCB231)
STOP-relay
+
Safety-relay
+
Relay
2 NO
+
1 NO
+
3 NC/NO
6A/130-250V AC1
+
6A/130-250V AC1
+
12A /130-250V AC1
6A/28V DC1
+
6A/28V DC1
+
12A/28V DC1
REL10 AC board
(PCB232)
Relay
10 NC/NO
12A /130-250V AC1
REL10 DC board
(PCB202)
Relay
10 NC/NO
12A/28V DC1
RELS DC board
(PCB203)
Relay
+
Safety-relay
8 NC/NO
+
1 NO
6A/130-250V AC1
6A/28V DC1
+
8A/28V DC1
REL13 DC board
(PCB204)
Relay
3 NO
12 NC/NO
12A/28V DC1
MOS8S board
(PCB205)
MOSFET
+
Safety-relay
8
+
1 (NO)
6A/28V (L=0) or
2A/28V (L=10mH)
+
8A/28V DC1
MOS10S board
MOSFET
10
6A/28V (L=0) or