Illinois Tool Works IJ4000 Operation Manual Download Page 24

Page: 24 / 78

IJ4000 Impulse Jet

Section 2: Quick Start

5765-018 Operations Manual Rev J

Page 24

Step 10: Mount Photosensor and Encoder

Photosensor
1. Position the photosensor (5760-383) upstream

from the first print head. The maximum place-
ment distance is 685,9mm [27in] from the pho-
tocell to the print head.

2. Refer to the instruction sheet included with the

photosensor for calibration.

3. Refer to the “Photosensor Sensitivity Test” on

page 41 of this manual to test the calibration.

Encoder
The encoder uses a wheel that rolls against the conveyor line to track the speed. It

sends a signal to the controller, which makes adjustments for reported changes in

the line speed.
It is not necessary to install the encoder immediately adjacent to the print heads. It is

more important to place it where it will accurately measure the speed of the con-

veyor. Install it in contact with the conveyor, or with a wheel or roller moving the

same speed as the conveyor.
The encoder's mounting bracket is spring-loaded. Adjust the spring collar to ensure

that the encoder maintains stable contact with the conveyor.

CAUTION:

Do not excessively pre-load the encoder wheel against the surface of

the conveyor. A radial force of over 18,14 kg [40 lbs.] will reduce the life of the bear-

ings.

Bracketry

Conveyor

Print Head

Conveyor

Encoder

Encoder Wheel

Spring

Summary of Contents for IJ4000















































































Search results

Summary of Contents for IJ4000

Reviews:

Related manuals for IJ4000

Brands by name

Popular brands

Illinois Tool Works IJ4000, Operation Manual

Search results

Summary of Contents for IJ4000

Reviews:

Related manuals for IJ4000

Brands by name

Popular brands