Illinois Tool Works IJ4000 Operation Manual Download Page 31

Page: 31 / 78

IJ4000 Impulse Jet

Section 3: Maintenance and Shutdowns

5765-018 Operations Manual Rev J

Page 31

Shutdowns of 3 Months or More

1. Follow recommendations for Shutdowns of 1 Week to 3 Months (see above).
2. It is recommended that the print head system be flushed with ScanTrue Flush Solution and that ScanTrue Flush Solution be left in the print

head and S

MART

-IDS during the storage period. (See “Consumables” on page 77 for part numbers.) Follow instructions in document

5760891N. Flush Solution can remain in the print head for one year from the date of flushing.

ACS - Automatic Cleaning System

NOTE:

If the beacon on the S

MART

-IDS is in any way illuminated or flashing, the ACS will not activate. Make sure all ink faults are corrected

before attempting an ACS.

The ACS is an invaluable tool for routine cleaning of loose debris from the print engine face. The images below demonstrate print before and

after the ACS.

BEFORE ACS

AFTER ACS

Summary of Contents for IJ4000















































































Search results

Summary of Contents for IJ4000

Reviews:

Related manuals for IJ4000

Brands by name

Popular brands

Illinois Tool Works IJ4000, Operation Manual

Search results

Summary of Contents for IJ4000

Reviews:

Related manuals for IJ4000

Brands by name

Popular brands