manualshive.com logo in svg

Ikegami OCP-100, Operation Manual, Page: 14 / 46

Share
Download
Ikegami OCP-100 Operation Manual Download Page 14

- PREVIEW switch

By pressing the top of the JOYSTICK, pins B and C of the PREVIEW connector (see item 30) will be short-circuited.

A

B

C

D

E

N.C

N.C

(DC5V 1mA)

PREVIEW switch

PREVIEW connector

IRIS control

M-PED control

   Note:

The operation of JOYSTICK is normally set to the relative value mode. It can be switched to the absolute value mode by 

changing the internal switch setting. Refer to

  

“ 3.6 Panel Config function” for how to switch the mode.

Relative value mode

 

:  In this mode, when the control is shifted from the MCP to the OCP, the IRIS value that is 

adjusted on the MCP is maintained regardless of the position of the IRIS RANGE control 

and JOYSTICK to prevent unintentional change of IRIS value. Operation may become one-

sided depending on the position of the control and JOYSTICK. The one-sided operation can 

be corrected by setting the control and JOYSTICK to the center position while holding down 

the KNOB FREE button.

Absolute value mode

  :  In this mode, the position of the IRIS RANGE control and JOYSTICK directly affects Open 

and Close of the IRIS.

16 CALL switch

Lights the R TALLY of the camera head and BS.

17 ALARM indicator

Flashes when an error is detected resulting from the self-diagnosis function. The diagnosis information is automatically 

displayed on the PM for about 20 seconds.

18  CABLE OPEN indicator

Lights when the triax or 

fi

 ber cable between the camera head and the BS is broken or not connected. This indicator is 

interlocked with the CABLE OPEN indicator on the front of the BS.

19  CABLE SHORT indicator

Lights when the triax or 

fi

 ber cable between the camera head and the BS is short circuited. This indicator is interlocked with 

the CABLE SHORT indicator on the front of the BS.

20  IRIS RANGE control

Used to set the center position of the IRIS CONTROL of the JOYSTICK (see item 15).

21  IRIS SENS control

Used to set the IRIS CONTROL range of the JOYSTICK (see item 15). The F-value between ±1 stop and ±2 stops can be set.

22  OPT LEVEL indicator

When the optical level of the Camera Head and CCU is normal, the GREEN lamp is turned on; at an attenuated level the 

ORANGE lamp and at an insuf

fi

 cient level the RED lamp is turned on.

1-6 

1. NAME and FUNCTION

OCP-100 

OCP-100 1209 VOL1 (U) (E)

Summary of Contents for OCP-100















































Reviews:

No comments