IKA MICROSTAR 15 control User Manual Download Page 6

 Unpacking 

17

16 Correct 

use

Unpacking

/// Scope of Delivery

Unpack the device carefully. 

Any damage should be notified immediately to 

the shipping agent (post office, railway network or logistics company).

Scope of Delivery

 

› MICROSTAR overhead stirrer

 

› power supply (with exchangeable adapters)

 

› extension arm

 

› hexagonal socket screw

 

› hexagon socket offset screw key

 

› shaft protector R 300 (with 2 fasten screws)

 

› chuck key

 

› USB cable

 

H 67.60

 temperature sensor

 

› user guide

 

› warranty card

MICROSTAR control

Warranty

+

+

+

+

+

+

+

+

Correct use

/// Basics

Use

 

› For mixing / stirring liquids from low to medium viscosities  

with various stirring tools.

 

Stand device 

(chuck points down)

Range of use 

(indoor use only)

 

› Laboratories

 

› Pharmacies

 

› Universities

 

› Schools

The safety of the user cannot be guaranteed:

 

› if the device is operated with accessories that are not supplied or  

recommended by the manufacturer.

 

› if the device is operated improperly or contrary to  

the manufacture’s specifications.

 

› if the device or the printed circuit board are modified by third parties.

Summary of Contents for MICROSTAR 15 control



















Reviews: