IKA 06-5819 Operating Instructions Manual Download Page 13

Page: 13 / 48

IKA

-WERKE

1.4.6 Working on electrical equipment

Info

Check whether the motor is running in the correct direc-
tion (arrow on the ventilator unit) by switching it on and
off briefly.

Info

The device connection must comply with VDE stan-
dards. Ensure that the motor voltage for the motor con-
nection and the mains voltage are identical. The motor
voltage is indicated on the motor rating plate or in the
technical data sheet.

Danger

•

Repair work on the machine's electrical equipment
may only be carried out by qualified electricians.

•

Check electrical equipment on a regular basis.

•

Secure loose connections.

•

Replace damaged lines/cables immediately.

•

Always keep the switching cabinet closed. Access is
only permitted to authorised personnel with the ap-
propriate keys/tools.

•

Never clean switching cabinets or other electrical
equipment enclosures by spraying with a water pipe.

Summary of Contents for 06-5819

















































Search results

Summary of Contents for 06-5819

Reviews:

Related manuals for 06-5819

Brands by name

Popular brands

IKA 06-5819, Operating Instructions Manual

Search results

Summary of Contents for 06-5819

Reviews:

Related manuals for 06-5819

Brands by name

Popular brands